Eden TERRA NOVA MODULE Manual Del Usuario página 2

1. Mute footswitch: Use this footswitch to
mute/un-mute the pedal.
2. Enhance footswitch: Use this footswitch to
turn the Enhance feature on/off.
3. Loop footswitch: Use this footswitch to
include/bypass the effects loop.
4. Active Input: Plug in your active or high
output bass here.
5. Passive Input: Plug in your passive or low
output bass here.
6. Compressor Switch: Use this switch to
turn the built in compressor circuit off
and on.
7. Input Gain: Use this control to adjust the
amount of signal sent into the preamp
stage. Use in conjunction with the Input
6
COMP
1. Power Inlet: Plug your supplied power
cord into your pedal using this mains
inlet socket.
2. DC Polarity Switch: Use this switch to
change the polarity of the pedal. To
use the supplied Eden 15V power unit
ensure the switch is set to centre positive.
Your pedal is suitable for use with power
supplies up to 18V.
3. Output (Left): Take your left signal output
EDEN is part of Marshall Amplification. For more information or to find your regional EDEN distributor visit our website www.edenamps.com
Eden Amplification, Denbigh Road, Bletchley, Milton Keynes, MK1 1DQ , ENGLAND - +44 (0)1908 375411 - info@edenamps.com
UNIT DIAGRAM - FRONT PANEL
Gain clip light to avoid clipping the input
stage of the pedal.
8. Input Gain Clip Light: When illuminated
this LED shows clipping is occurring in
the preamp. To prevent this either turn
down the output of your instrument, or
dial the Input Gain to a lower setting.
9. Enhance: The Enhance circuit provides
an easy-to-use EQ sweep, allowing you
to simultaneously boost very low bass,
upper middle and high frequencies,
while cutting the lower mid frequencies.
Quickly find your sound before adjusting
the finer EQ details. For best results use
the Enhance control with all other EQ
settings at 12 O'clock before detailing
your tone.
8
CLIP
12
7 9
BOOST
INPUT ENHANCE
10
GAIN
-15 +15
BASS
MUTE MUTE
1
UNIT DIAGRAM - BACK PANEL
to external equipment here.
4. Output (Right): Take your right signal
output to external equipment here.
5. Aux In: Connect an external device using
a 3.5mm jack cable here.
6. Headphone Out: Connect your
headphones here using standard 3.5mm
headphone cable.
7. DI Ground Lift: Lift ground from your
2
DC
POLARITY OUTPUT (R)
1
15-18V DC IN OUTPUT (L)
10. Bass: Adjust the low frequencies of the
pedal using this control.
11. Bass Boost Switch: Use this switch to
turn on the Bass Boost feature on the
pedal. When engaged the Bass control
will provide more pronounced Bass
adjustment.
12. Bass Boost Light: When illuminated this
LED indicated the Bass Boost feature is
turned on.
13. Low Mid Control: Change the amount
of frequency adjustment by the Low Mid
Freq Sweep using this dial.
14. Low Mid Freq Sweep: Adjust the
frequency affected by the Low Mid
control from 30 Hz up to 300 Hz using
this control.
165 1.1K
14 16 17
30 300 200 2K -15 +15
TREBLE
11
13 15
-15 +15 -15 +15
LOW MID HI MID
ENHANCE ENHANCE
2
signal (when required) using this switch.
8. DI Pad: Pad the signal (reduce the
output level) between line level and mic
level using this switch.
9. DI Pre / Post Select: Choose to take the
DI signal from either before or after the
preamp shaping circuit inside the pedal.
10. DI Output: Connect to either a mixing
desk, front of house system or recording
7 8 9
GND DI OUT PRE/
LIFT LEVEL POST
5
4
AUX IN
6
10
3
PHONES
DI OUT
15. Hi Mid Level Control: Adjust the
frequency affected by the Hi Mid Freq
Sweep using this control.
16. Hi Mid Freq Sweep: Adjust the frequency
affected by the Hi Mid Level control from
200 Hz up to 2000 Hz using this control.
17. Treble: Adjust the highest frequencies on
the pedal using this control.
18. Master: Use this control to adjust the
overall output volume of the pedal.
19. Master Clip Light: This LED will illuminate
if anything causes the output to clip.
20. Logo: This logo will illuminate when the
pedal is switched on.
BASS PREAMP PEDAL
CLIP
20
19
18
MASTER
LOOP LOOP
3
device using a standard XLR cable.
11. Loop Send: Take your signal to your
external effect loop or outboard
equipment from here.
12. Loop Return: Return your signal from
any outboard equipment or effect loop
here.
13. Tuner Out: Take your tuner signal out
from this socket.
12
RETURN
11 13
SEND TUNER
4
5