Preliminary Procedures - Vimar ELVOX 7549 Instrucciones Instalador

TAB: 7549

Preliminary procedures

After having installed the device, it must be programmed, giving it
an identification number
(ID), which is unique for each appliance.
The BASIC programming is described below, which can be done
with the device's keyboard.
All programming operations must be performed with the in-
door unit on standby.
For ADVANCED programming, use the SaveProg software for
PC.
Programming ID identification code
The identification code is programmed with a configured MASTER
entrance panel.
An indoor unit with no ID code programming beeps three times
when the button is pressed
1) Lift the handset.
2) Press the and buttons simultaneously and keep them
pressed until the button starts blinking.
3) Release the buttons.
4) Press the button within 5s of releasing the buttons and
keep it pressed until you hear a warning tone on the handset
and the communication is activated between the indoor unit
and the external electronic unit. If more than 5s passes with-
out the button being pressed, steps 1, 2 and 3 must be
repeated.
5) Release the button.
6) Within 25s, pair the ID code from the external electronic unit,
following the procedure described on the speech unit (pushing
a button, internal keyboard entry).
NOTE: If the installation already contains an indoor unit with the
same paired identification code, the entrance panel will emit a
tone and the process must be repeated from the start in order to
assign a different code.
Programming secondary ID
The secondary identification code is programmed when the same
call has to activate multiple indoor units at the same time (max
4 composed of 1 Master and 3 secondary ones). You need to
define a Master indoor unit which can be paired with up to 3 indoor
units with a secondary ID. At most 50 Master ID codes can be
programmed in this way.
1) Lift the handset of the indoor unit.
2) Press the and buttons simultaneously and keep them
pressed until the button starts blinking.
3) Release the buttons.
4) Press the and
releasing the buttons and keep them pressed until you hear a
warning tone on the indoor unit and the communication is acti-
vated between the indoor unit and the external electronic unit. If
more than 5s passes without the
pressed, steps 1, 2 and 3 must be repeated.
5) Release the and
buttons simultaneously within 5s of
and buttons being
buttons.
6) Within 25s, pair the ID code of the Master from the electron-
ic unit, following the procedure described on the speech unit
(pushing a button, internal keyboard entry).
Note: Use the SaveProg software to program chime activation of
all the monitors and switching on only the master monitor.
Note: To delete from a group, the programming deletion proce-
dure described in the "Default data restore procedure" section
must be performed.
Button programming procedure for intercom-
municating calls
1) Raise the handset of the indoor unit to program (caller).
2) Press the and
(caller) and keep them pressed until the
ing.
3) Release the buttons.
4) Press and hold down the calling button to be programmed (
/ / / / ).
5) Wait for the indoor unit to emit a continuous tone.
6) Release the button you wish to program for the calling indoor
unit.
7) Press a button on the indoor unit to call (
8) An audible warning on the calling indoor unit confirms that the
procedure has correctly completed.
Programming the self-start button for a specific
electronic unit
1) Lift the handset.
2) Press the and
pressed until the button starts blinking.
3) Release the buttons.
4) Press and hold down the button you want to program ( /
/ / ).
5) Wait for the indoor unit to emit an audible warning.
6) Release the button.
7) Call the indoor unit from the entrance panel on which you want
direct self-starting (pressing a button, internal keyboard entry
or selecting the name from the contacts list).
8) At the end of the procedure described above, the indoor unit
emits a signal to confirm that the operation has been success-
ful and it is called by the entrance panel.
Procedure for restoring default data for each
individual button ( /
1) Lift the handset.
2) Press the and
pressed until the button starts blinking.
3) Release the buttons.
4) Press and hold down the button to be restored to the default
programming ( / /
5) Release the button and press the button again, the indoor unit
EN
buttons of the indoor unit to program
button starts blink-
/F1/F2/
buttons simultaneously and keep them
/ / / )
buttons simultaneously and keep them
/ / ) until the indoor unit beeps.
).
/
19