General Instructions - GLOBBER EVO COMFORT PLAY Serie Manual Del Usaurio

Keep the instructions for future.
NF-EN-71
Warning! Protective equipment should be worn. Not to be used in traffic.
20 kg max.: Seat mode (pushchair, ride-on)
50 kg max.: Scooter mode
Seat mode: Warning! Not to be used by children over 36 months due to the limited
strength of the seat bracket frame. The seat can only be used with this product
when the steering is completely locked by the parents using the locking button
located at the upper side of the steering assembly. Press down the locking button
in order to lock the steering of the wheels when the seat is to be mounted.
Remove the scooter and all the parts from the box. Set out all the parts and read
the assembly instructions prior to use. Keep the packaging until assembly is
complete.

General instructions

This toy must be assembled by a responsible adult. Prior to use, make sure
that the toy has been assembled properly. Remove all the parts which are not
necessary for play before giving the toy to your child. The toy should be used with
caution since skill is required to avoid falls or collisions causing injury to the user
or third parties.
To use with suitable protective equipment, including a helmet, shoes, elbow, wrist
and knee protectors. Teach the child how to use it safely and responsibly.
Directions:
- T he scooter can be dangerous and can cause traffic accidents when used
on public highways. Don't use on public roads. It is best used on a flat, clean
surface, free of gravel and grease. Avoid bumps and drainage grates that may
cause an accident.
- The scooter does not include any headlights or lights. It is therefore not suited for
use at night or during periods when visibility is limited.
- Always use under adult supervision.
- Do not allow more than one child to ride the scooter at the same time.
- Do not use on wet days, or on wet ground.
Before and after use:
- Make sure that all locking mechanisms are securely locked.
- Check the height of the steering system, and make sure the nuts are tightened
and that the handlebars and the front wheel are perpendicular.
- The minimum height of T-bar has to be locked at the lowest position by switching
the bullet into the lowest hole (see diagram E).
- Check all of the connection elements: the brake, the steering column's quick
release system and the wheel axles must be adjusted correctly and not
damaged.
6
- Also check the tyre wear.
INSTALLATION AND USE OF SEAT FOR USE
Pushchair / Ride-on (See page 2)
EVO COMFORT comes with a sturdy seat support frame to better distribute
the load of the seated child. There are 3 different seat heights available. For a
comfortable ride, your child's feet should easily touch the footrest. Attach the seat
to the seat support bar by screwing in the 2 hex screws. Both screws must be
securely fixed. (Figure 2).
Pushchair mode:
Place the footrest at the front of the deck in the correct direction (see diagram 3b).
Hook the seat bracket frame latch from underneath over the front wheel steering
assembly and screw them tight with the thumb screw through the center hole
(Figure 3a). Insert the handlebar tube in the back hole of the seat support frame.
Align the spring-loaded button with the rectangular notch in the seat support frame
and lock (Figure 4b). Double check that the spring-loaded button is engaged
and locked correctly (Figure 4a). Adjust the height of the handle to the parent's
preference (4 positions are possible, see diagram E). Loosen the quick release
clamp of the T-bar handle when adjusting. Tighten the quick release clamp to
secure the T-bar handle after adjustment. Always fix the coloured screw-like
component on the deck if the footrest is removed. (See diagram A)
Ride-on mode:
- Remove the handlebars' tube in the back hole of the seat support frame. Always
fix the coloured screw-like component on the deck if the footrest is removed (see
diagram A).
- EVO COMFORT is provided with an adjustable seat which can be adapted to
the child's height (3 positions). Attach the seat through 2 of the screw holes in the
seat support frame.
Steering: The child pushes with his feet on the floor to advance, while the child's
sitting on the seat. He must proceed with caution at first. The parent handlebars
can be used to accompany children during first use.
Install the foot rest (see diagram 3b). Place the child's feet on the footrest and the
adult pushes using the parent handle (T-bar).
Scooter mode:
Insert the handle bar (t-bar) tube into the hole at the front of the deck between the
two front wheels while paying attention to the direction of insertion. Ensure the
spring loaded-ball pops out and locks the bar in place properly (see diagram A).