Safety Warnings - Zucchettikos SILKSTONE TRAY Instrucciones Para La Instalación Y Uso

ENGLISH

SAFETY WARNINGS

Before installing the unit, carefully read this
booklet, which must be kept with care for future
use by the various operators.
If any parts of this booklet are unclear, contact
the Manufacturer for any additional clarifications
that may be needed.
The installation of the equipment must be car-
ried out by qualified personnel, authorised to
issue appropriate conformity documentation in
accordance with the current legislations of the
country of installation.
interventions, tampering or modifications
Any
not expressly authorised, and not in compliance
with the indications of this manual, may cause
damage, injury or death, and will automatically
void the manufacturer warranty.
When installing the unit always use appropriate
personal protective equipment (e.g. gloves,
safety shoes, etc.)
During the assembly of the unit, no people not
in charge of the installation operations must be
allowed to transit or station in the direct proxim-
ity of the installation area.
Being potentially dangerous, packaging mate-
rial must be kept out of reach of children or
animals, and must be correctly disposed of in
accordance with local legislations. Kos invites to
protect the environment by disposing of the
materials in the appropriate sorted waste dis-
posal containers.
Maintenance must be carried out by the Kos
technical support service, or by authorised spe-
cialist personnel, only using spare parts ap-
proved by Kos. In case of use of unapproved
spare parts, the warranty will become void, and
the manufacturer shall not be liable for any
damage caused by its products.
INSTALLATION
BEFORE STARTING:
Observe all of the local hydraulic and building regulations.
The following instructions are to be followed by qualified personnel with the
technical background and experience needed to manage the product safely.
This shower tray should only be used in domestic environments at room
temperature.
The Manufacturer shall not be held responsible and the warranty shall no
longer be valid in case of improper use.
Open the package and inspect the shower tray for damage.
Before installing the product, use a metallic bar or ruler to make sure the
product has not warped due to improper storage. In case of improper
installation, warranty will decay.
In case of installation of a warped/deformed product, warranty will decay.
A 2 mm distortion per linear metre is within the tolerances of manufacture
and is therefore not to be considered a defect. Place the shower tray back
in the carton until it is installed. Before installing, check access to the final
hydraulic connections.
To prevent water stagnation, the shower jet must fall entirely and exactly
within the shower tray, preferably above the drain (and never above the at
standing/walk-in area). Warranty will decay in case of improper installation.
PREPARING THE LOCATION:
Make sure the floor and the supporting surfaces are at and leveled.
Drill a hole that is wide enough to contain the appropriate drainage kit
needed for the drainage system. The hole must be appropriately
located and while keeping the position and size of the shower tray in mind.
PREPARING THE SHOWER TRAY:
Extract the shower tray from the packaging, which should be disposed of
in accordance with the local regulations in force.
Install the drainage kit on the shower tray as indicated by the Manufacturer.
Position the shower tray where it shall be installed (raised by means of
wooden blocks) and fasten all the hydraulic connections of the drainage
system.
Open the faucets and let the water run inside the shower tray. Check all the
connections for possible leaks.
Place the shower tray on the floor and make sure it is perfectly at. Seal the
entire perimeter of the shower tray with acetic silicone. If the shower tray is
slightly above the floor, or semi-embedded, leave 2-3 mm of space around
the entire perimeter (which must be sealed with acetic silicone); as to make
room for the thermal expansion of the material.
Let the silicone dry for at least 24 hours before using the shower tray (or
before mounting any shower walls).
Protect the surface of the shower tray from mortar, glue or putty used to
install the shower cubicle, tiles or for any other installation.
6