Flint & Walling 3SDPH-L Instrucciones De Instalación página 2

FOR YOUR PROTECTION, ALWAYS DISCONNECT
PUMP FROM ITS POWER SOURCE BEFORE HANDLING. Single
phase pumps are supplied with a 3-prong grounded plug to help
protect you against the possibility of electrical shock. DO NOT UNDER ANY
CIRCUMSTANCES REMOVE THE GROUND PIN. The 3-prong plug must be
inserted into a mating 3-prong grounded receptacle. If the installation does
not have such a receptacle, it must be changed to the proper type, wired and
grounded in accordance with the National Electrical Code and all applicable
local codes and ordinances. Three phase pumps require motor starting devices
with motor overload protection. Pumps must be installed in accordance with the
National Electrical Code and all applicable local codes and ordinances. Pumps
are not to be installed in locations classified as hazardous in accordance with
National Electrical Code, ANSI/NFPA 70.
"Risk of electrical shock" Do not remove power
supply cord and strain relief or connect conduit directly to the pump.
Installation and servicing of electrical circuits and
hardware should be performed by a qualified licensed electrician.
Pump installation and servicing should be performed
by a qualified person.
Manufacturer warrants, to the purchaser and subsequent owner during
the warranty period, every new product to be free from defects in material
and workmanship under normal use and service, when properly used and
maintained, for a period of one year from date of purchase by the end user, or
18 months from date of original manufacture of the product, whichever comes
first. Parts that fail within the warranty period, one year from date of purchase
by the end user, or 18 months from the date of original manufacture of the
product, whichever comes first, that inspections determine to be defective
in material or workmanship, will be repaired, replaced or remanufactured
at Manufacturer's option, provided however, that by so doing we will not be
obligated to replace an entire assembly, the entire mechanism or the complete
unit. No allowance will be made for shipping charges, damages, labor or
other charges that may occur due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any
material or product that has been disassembled without prior approval of
Manufacturer, subjected to misuse, misapplication, neglect, alteration, accident
or uncontrollable act of nature; that has not been installed, operated or
maintained in accordance with Manufacturer's installation instructions; that has
been exposed to outside substances including but not limited to the following:
sand, gravel, cement, mud, tar, hydrocarbons, hydrocarbon derivatives (oil,
In instances where property damages are incurred as a result of an alleged product failure, the property owner must retain possession
EASY DO'S & DON'T'S FOR INSTALLING A SUMP PUMP
1. DO read all installation material with the unit.
2. DO inspect unit for any visible damage caused by shipping. Contact
dealer if unit appears to be damaged.
3. DO remove all debris from the basin. Be sure that the pump will have a
hard, level surface beneath it. DO NOT install on sand, gravel or dirt.
4. DO be sure that the area is large enough to allow proper clearance for
the level control switch(es) to operate properly.
5. DO Always Disconnect Pump From Power Source Before Handling.
DO always connect to a separately protected and properly grounded
circuit.
DO NOT ever cut, splice, or damage power cord (Only splice in a watertight
junction box).
DO NOT carry or lift pump by its power cord.
DO NOT use an extension cord.
6. DO install a check valve and a union in the discharge line.
CAUTION
up which may interfere with the float "on" or "off" position. Repair and service
should be performed by an Authorized Service Station only.
CAUTION
use in pits handling raw sewage.
CAUTION
exceed 130 °F (54 °C). Thermoplastic pumps must not exceed 110 ºF (43 ºC).
CAUTION
"off - on" level controls.
CAUTION
Do not attempt to start pump when tilted or laying on its side.
CAUTION
Dynamic Head is less than the minimum Total Dynamic Head listed on the
Head/Capacity Curves.
LIMITED WARRANTY
gasoline, solvents, etc.), or other abrasive or corrosive substances, wash towels
or feminine sanitary products, etc. in all pumping applications. The warranty
set out in the paragraph above is in lieu of all other warranties expressed or
implied; and we do not authorize any representative or other person to assume
for us any other liability in connection with our products.
Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky 40211,
Attention: Customer Support Department to obtain any needed repair or
replacement of part(s) or additional information pertaining to our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF
EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY
OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY
SHALL BE LIMITED TO THE DURATION OF THE EXPRESSED WARRANTY.
Some states do not allow limitations on the duration of an implied warranty,
so the above limitation may not apply to you. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
of the product for investigation purposes.
DO NOT use a discharge pipe smaller than the pump discharge.
7. DO NOT utilize this unit for pumping gasoline or other hazardous liquids.
8. DO test pump immediately after installation to be sure the system is
working properly.
9. DO review all applicable governing codes and verify that the installation
conforms to each of them.
10. DO consult manufacturer for clarifications or questions.
11. DO consider a two-pump system with an alarm where an installation may
become overloaded or primary pump failure would result in property damages.
12. DO consider a D.C. Backup System where a sump or dewatering pump
is necessary for the prevention of property damages from flooding due
to A.C. power disruptions, mechanical or electrical problems or system
overloading.
13. DO inspect and test system for proper operations at least every 3 months.
© All rights reserved.
2
Pump should be checked frequently for debris and/or build
Dewatering and effluent sump pumps are not designed for
Maximum operating temperature for cast iron pumps must not
CSA certified pumps must be operated submerged with
Submersible pumps must be operated in an upright position.
Do not operate a pump in an application where the Total