Installation Instructions; Required Tools - Acuity Brands Lithonia Lighting OLF 2RH 40K 120 Guía De Paso-A-Paso

FIXTURE PACKING LIST
Description
1) LED Light Fixture................................................................. 1
2) Photocontrol with adjustable cover (PE model only) ........... 1
3) 1-1/4"(2H) & 2"(3H) Mounting Screw ................................. 1
4) Cross Bar ............................................................................ 1
5) 3/4" #8 & #6 & #10 screws* ................................................. 6
6) Wire Nuts* ........................................................................... 3
7) Rubber Plug* ....................................................................... 1
8) Lock Nut ................................................................2 or 3 or 4
9) Adjustment Knob .......................................................... 2 or 3
10) Visor (Round Head only) ............................................. 2 or 3
11) Set Screw (Round Head only) ..................................... 4 or 6
12) Support Hook* .................................................................... 1
*Contained in parts packs
Mounting Hardware Included
Silicone Sealant Required

REQUIRED TOOLS:

1. Remove fi xture components and parts pack. Check to
ensure all parts are included. Note: Account for small parts and
destroy packing material, as these may be hazardous to children.
2. Turn OFF Power at circuit breaker box.
CAUTION: Do not rely on wall switch alone to turn off power.
Note: Suitable for wall mount or eave mount.
Not suitable for ground mount installation.
3. Install cross bar (4) to your junction box using two 3/4" #6 or #8
or #10 screws (5) (screw size is depending on your junction box).
4. Hang one end of the support hook (12) onto the cross bar
and hang the light fi xture on the other end of the support hook to
temprarily support fi xture for wiring. See Fig.B
CAUTION: WIRING AND FIXTURE OPERATION
Make sure power is turned off. Connect to 120V, 60Hz circuit only.
5. To Ground fi xture use wire nut (6) to connect the (copper)
house supply ground wire & the green fi xture ground wire. Note:
If house wiring does not include a ground wire, consult your local
electrical code for approved grounding methods.
For proper connection, place wire nut over wires
and twist clockwise until tight.
6. To Connect supply wires use wire nut (6) to connect the black
fi xture wire to the black power supply wire and the white fi xture
wire to the white (neutral) supply wire.
7. To Install fi xture insert mounting screw (3) into center hole of
fi xture housing. Align fi xture over j-box and secure to cross bar by
tightening mounting screw. Cover center hole in fi xture housing
with rubber plug (7). See Fig A. Note: make sure no wires are
pinched before tightening.
8. Aim lamp heads and install optional visor (round heads)
Each lamphead can be positioned in multiple directions via
the adjustment knob (9) and the lock nut (8). Note: Make sure
to secure all lock nuts and adjustment knobs tightly (do not
overtighten) after fi nal adjustments are made to avoid water entry.
CAUTION - Risk of Shock: Aim lamp heads at least

INSTALLATION INSTRUCTIONS

Quantity
7) Rubber Plug
3) Mounting Screw
Figure A
20° down below horizontal in order to prevent water from
accumulating inside lens.
After lamp heads are positioned as desired, align the optional
visor (10) over the front of the round lamp head and secure by
tightening the set screws (11) on the visor.
9. Turn on electricity at fuse or circuit breaker box and verify
success of installation. Note: on models with photocell, adjust
photocontrol cover so that the window is fully open. See Trouble
shooing guide for more info.
10. Apply silicone caulking (not included) around the perimeter
of the fi xture back where it contacts the mounting surface for
moisture seal.
8) Lock Nut
page 3
9) Adjustment Knob
1) LED Light Fixture
4) Cross Bar
2) Photocontrol
6) Wire Nuts
12) Support Hook
10) Visor
11) Set Screw
5) 3/4" Screws
Figure B