Changing Cycles, Options And Modifiers; End Of Cycle Signal; Tumble Free™ Heated Dryer Rack - KENMORE ELITE HE5 Steam 110.9772 Manual De Uso Y Cuidado

Temperature
Press TEMPERATURE until the desired temperature setting
glows. Temperature modifiers cannot be used with the Auto
Cycles or with Rack Dry or Timed Dry/Air Dry cycles.
Dryness Level
Press DRYNESS LEVEL until the desired Dryness Level is
selected. Dryness Level cannot be adjusted with Timed Cycles.

Changing Cycles, Options and Modifiers

You can change Auto Cycles, Timed Cycles, Modifiers and
Options anytime before pressing Start.
Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles after pressing Start
1. Press STOP twice. This ends the current cycle.
2. Select the desired cycle and options.
3. Press and hold START. The dryer starts at the beginning of
the new cycle.
NOTE: If you do not press START within 5 minutes of selecting
the cycle, the dryer automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.
1. Press STOP once.
2. Select the new Modifier and/or Option.
3. Press and hold START to continue the cycle.
NOTE: If you happen to press Stop twice, the program clears and
your dryer shuts down. Restart the selection process.
Changing the Preset Dryness Level Settings
If all of your loads on all Auto Dry cycles are consistently not as
dry as you would like, you may change the preset Dryness Level
settings to increase the dryness. This change will affect all of your
Auto Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different
installations, environmental conditions or personal preference.
There are 3 drying settings: 1 (factory preset dryness level),
2 (slightly dryer clothes, approximately 15% more drying time)
and 3 (much dryer clothes, approximately 30% more drying
time).
20
1. The Dryness Level settings cannot be changed while the
dryer is running.
2. Press and hold the DRYNESS LEVEL button for 5 seconds.
The dryer will beep, and "CF" will be displayed for 1 second
followed by the current drying setting.
3. To select a new drying setting, press the DRYNESS LEVEL
button again until the desired drying setting is shown.
NOTE: While cycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press START to save the drying setting.
The drying setting you selected will become your new preset
drying setting for all Auto Dry cycles.

End of Cycle Signal

End of Cycle Signal
The End of Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end of
the cycle reduces wrinkling.
Press CYCLE SIGNAL to adjust the sound level or turn off the
signal.
NOTE: When WRINKLE GUARD
Cycle Signal is on, a tone sounds every 5 minutes until the
clothes are removed, or WRINKLE GUARD
TUMBLE FREE™ Heated Dryer Rack
The dryer rack is shipped in place in your dryer. Remove and
discard any packing material before use.
Use the TUMBLE FREE™ Heated Dryer Rack for items that you
do not want to tumble dry, such as sweaters. When you use the
heated dryer rack, the heated air inside the dryer flows in a
concentrated pattern to allow efficient and uniform drying.
The dryer rack is recommended for use with the Rack Dry or
Timed Dry/Air Dry cycles. The dryer rack cannot be used with
Auto cycles.
To use the heated dryer rack:
Do not remove the lint screen.
1. Open dryer door.
2. Place dryer rack over the bottom of the dryer door opening.
Rest the back wire on the dryer back ledge. Push down on
the frame front to secure over lint screen.
® is selected and the End of
® ends.