Descargar Imprimir esta página

Disposal Information - Multiplex EasyStar BL Tuning Manual De Instrucciones

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

Motor mounting after assembling of the model:
1. Use a very thin-bladed, sharp knife to cut through the
top seam line of your EasyStar as far as the cabin
area, as illustrated in fig.3. Carefully spread the top
opening in the foam only a little bit in the area of the
motor mount, so that you can withdraw the 400
brushed motor with it's cables. Once you have
removed the original motor, you can glue the BL-motor
as described below.
2. Glue the Himax BL-motor into the left half of the
fuselage, making it protrude by approx. 3 mm as
illustrated in fig. 2. Secure the motor only punctual with
Zacki ELAPOR
in the fuselage, so that you would be
®
able to unhinge it again, later. Ensure that no glue gets
into the motor.
3. Lay the motor cables in the corresponding cable
channel.
4. Glue the cut foam edges together again, as illustrated
in fig. 4.
5. Fix the driver to the motor shaft
6. Fix the Propeller (impressed script shows backwards)
to the driver by using the included spinner
Fig.3
Fig.4
6. I
NITIATION OF THE
"E
S
BL-TUNING"
ASY
TAR
1. Connect the three wires attached to the speed
controller to the three wires attached to the motor; the
order of connection is unimportant.
2. Locate the UNI connector attached to the speed
controller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the "OFF" position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking
forward. If this is not the case, disconnect the flight
battery and swap over any two of the three motor wires.
6. Switch ON the motor brake at the speed controller; the
method of doing this is described in the instructions
supplied with the controller.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating Instructions for Power Set "EasyStar BL-TUNING"
P
S
OWER
ET
7. H
-
IMAX MOTOR
Type:
#
RPM / V:
Cell count, NiXX / LiPo:
Efficient operating current:
Max. current for 15 sec.:
Shaft Ø:
Diameter:
Length:
Weight:
Max. output:
Max. case temperature:
Mounting:
You will find comprehensive operating instructions for the
Himax
B
2810-2150
DOWNLOADS
INSTRUCTIONS.
8. G
UARANTEE
MULTIPLEX products are covered by the statutory guarantee
regulations. If you wish to make a claim under guarantee,
please contact the model shop where you purchased the
product in the first instance.
The guarantee does not cover damage and malfunctions
caused by:
• Improper handling, incorrect connections, reversed polarity
• Use of accessories other than genuine MULTIPLEX items
• Modifications or repairs not carried out by MULTIPLEX or an
authorised MULTIPLEX Service Centre
• Accidental or deliberate damage
• Defects due to normal wear and tear
Use outside the technical specifications
9. CE A
PPROVAL
This product satisfies all the relevant statutory
harmonised EU directives.
You are therefore the owner of a product whose design
fulfils the protective aims of the European Community relating to
the safe operation of equipment.
You are entitled to obtain a copy of the conformity declaration
for this product by contacting MULTIPLEX using the information
at the foot of the page.
10.
D
I
ISPOSAL
NFORMATION
Electrical equipment marked with the cancelled
waste bin symbol must not be discarded in the
standard household waste; instead it must be taken
to a suitable specialist disposal system.
In the countries of the EU (European Union),
electrical equipment must not be discarded via the normal
domestic refuse system (WEEE – Waste of Electrical and
Electronic Equipment, directive 2002/96/EG). You can take
unwanted equipment to your nearest local authority waste
collection point or recycling centre, where the items will be
disposed of correctly and at no cost to you.
By returning your unwanted equipment you can make an
important contribution to the protection of the environment.
SPECIFICATION
B 2810-2150
33 3043
2150
6 - 9 / 2S - 3S
10 A - 18 A
24 A
2.3 mm
28 mm
31.0 mm
65 g
160 W
100° C
∅ 16 mm / 4 x M3
at
www.multiplex-rc.de
Page 2/2

Publicidad

loading