Peg-Perego MAXI DIESEL TRACTOR Empleo Y Manutencion página 9

ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING.
ASSEMBLY
1 • Remove the 4 protective caps from the axles.
2 • Put the seat on its base. Please note: The seat can
be put in 2 different positions, as shown in the
figure.
3 • Secure the seat in the desired position with the
2 screws provided.
4 • Insert the front part of the unit that you have
just assembled in the 2 slots in the chassis.
5 • Secure it at the rear with the 2 screws provided.
6 • Insert the roll bar in the bodywork, as shown in
the figure.
7 • Secure it with the 2 screws provided.
8 • Turn the red coupling pin so that the cab can be
opened (1). Release the cab. Fully insert the hinge
at the front of the chassis (2). Close the cab (3)
and secure it by turning the red pin 180°.
9 • Click together the 2 parts of the steering wheel.
10 • Follow the instructions in the packaging of the
horn to insert it in the hole in the centre of the
steering wheel.
11 • Push the steering column up from below and slot
the steering wheel onto it.
12 • Line up the holes in the steering column and the
steering wheel. Secure the steering wheel with
the screw and the nut: the nut goes in the
hexagonal hole and the screw in the round hole.
13 • Before fitting the front wheels (the smaller ones),
ensure that the internal bushes and wheel trims
are present. Put the following on the left steering
lever, in this order: a washer, the front left wheel
(see the label inside the wheel) and another
washer.
14 • Put one of the bigger self-locking washers into
the special tool, as shown in the figure. The tabs
on the self-locking washer must face towards the
inside of the tool (see detail A). PLEASE NOTE:
The bag contains more self-locking washers than
you will need. Keep the others as spares in case
one breaks.
15 • Push the self-locking washer all the way down to
secure the wheel, as shown in the figure. Repeat
the procedure to fit the other front wheel.
16 • Before fitting the rear wheels, ensure that the
internal bushes and wheel trims are present.
Insert the left rear wheel (see the label inside
the wheel). Make sure that the shape of the axle
fits properly into the bush of the wheel (detail
A). Insert a flat washer.
17 • Insert a self-locking washer in the special tool
provided. PLEASE NOTE: The tabs on the self-
locking washer must face towards the inside of
the tool (see detail A).
18 • Secure the rear left wheel with a hammer, as
shown in the figure.
19 • Leave one of the special conical tools in the left
wheel and lay the toy on its left-hand side. Insert
the following, in this order: the other rear wheel,
a flat washer and the special tool, with a self-
locking washer inside it. Secure the wheel with a
hammer, as shown in the figure.
20 • Click the 2 small caps onto the rear wheels and
the big ones onto the front wheels.
21 • Put the silver stickers on the rear lights.
22 • Fit the 2 rear lights. Slot in the lower part first
and then the upper part, as shown in the figure.
23 • Put the silver sticker on the front headlight and
click on all of the headlight clips.
TRAILER
Follow the instructions below to assemble the trailer.
24 • Insert one of the 4 self-locking washers (there
are 2 spares) in the special tool provided.
PLEASE NOTE: The tabs on the self-locking
washer must face towards the inside of the tool
(see detail A).
25 • Remove the axle from the packaging and take off
its protective caps. Use a hammer to hit the axle
all the way down into the tool provided, then
remove the tool.
26 • Click the wheel trims onto the wheels. Put the
following items on the axles, in this order: a
washer, a wheel, the other wheel, a washer (4
washers are provided, 2 of which are spares).
PLEASE NOTE: Make sure that the bushes are
present in the wheels and that the wheels are
fitted correctly, with the wheel trims facing
outwards.
27 • Put a self-locking washer in the special tool,
insert the axle that you prepared earlier and hit
it all of the way in with a hammer.
28 • Slot the wheel unit into the bottom of the
trailer.
29 • Insert the red clip in the end of the trailer.
30 • Clip the bottom of the trailer that you prepared
earlier into the body, as shown in the figure.
31 • Assemble the 3 sides of the trailer. Ensure that
the parts with the wooden effect are facing
outwards.
32 • Fit the assembled parts into the slots in the
body of the trailer.
33 • Put the 2 remaining caps onto the wheels of the
trailer.
34 • To attach the trailer to the tractor, insert the
clip on the trailer in the hole at the back of the
tractor and turn it (see fig. 35).
35 • Position 1: The trailer can be removed. Position
2: The trailer is attached. PLEASE NOTE: The
trailer can hold items with a maximum total
weight of 10 kg.
VEHICLE FEATURES AND INSTRUCTIONS
FOR USE
36 • DRINK HOLDER: A convenient drink holder
situated near the seat.
37 • HORN: There is a horn on the steering wheel of
the vehicle.
38 • ADJUSTING THE PEDALS: The pedals can be
put in 2 different positions to cater to the height
of the child. POSITION A (the upper one) is for
smaller children and POSITION B (the lower
one) is for bigger children. The 2 positions are
marked with 2 different colored dots on the
corresponding sticker. Remove the 3 screws
holding the pedal adjustment disk (which are
shown on the sticker with symbols) and rotate
it to the desired position, then tighten the 3
screws. PLEASE NOTE: Put both adjustment
disks in the same position (upper or lower) on
both sides.
39 • ADJUSTING THE SEAT: The seat can be put in 2
different positions to cater to the growth of the
child. See figure 2 for details.
40 • OPENING HOOD: Use a coin to turn the red
clip as far as the position shown in the figure.
Inside the hood is a large storage compartment.