Johnson Controls tyco GS4015 Guia De Instalacion página 93

FCC Compliance Statement
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not
installed and used properly, in strict accordance with the manufacturer's
instructions, may cause interference to radio and television reception. It has
been type tested and found to comply with the limits for Class B device in
accordance with the specifications in Subpart "B" of Part 15 of FCC Rules,
which are designed to provide reasonable protection against such interfer-
ence in any residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause interference to television or radio reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

Re-orient the receiving antenna

Relocate the alarm control with respect to the receiver

Move the alarm control away from the receiver

Connect the alarm control into a different outlet so that alarm control
and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/
television technician for additional suggestions. The user may find the fol-
lowing booklet prepared by the FCC helpful: "How to Identify and Resolve
Radio/Television Interference Problems". This booklet is available from
the U.S. Government Printing Office, Washington, D.C. 20402, Stock #
004-000-00345-4.
Wireless Notice
This equipment complies with FCC and IC radiation exposure limits set
forth for an uncontrolled environment. The antenna should be installed and
operated with minimum distance of 20 cm between the radiator and your
body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Antenna gain must be below:
Band
2G
B1 (2100) X
B2 (1900) X X
B3 (1800) X
B4 (1700) X
B5 (850) X X
B7 (2600)
B8 (900) X
B28 (700)
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this
equipment is a label that contains, among other information, the FCC regis-
tration number and ringer equivalence number (REN) for this equipment. If
requested, this number must be provided to the Telephone Company.
TL405LE-LAT Product Identifier US:F53MO00ATL405LE
REN:0.0A
USOC Jack:RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and mod-
ular plug is provided with this product. It is designed to be connected to a
GS4015/GS4005/3G4005/TL405LE
TL405LE-LAT
HSPA+ LTE FDD Ant Gain
X
X
X
X
X
X
X
compatible modular jack that is also compliant. See installation instruc-
tions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be con-
nected to a telephone line. Excessive RENs on a telephone line may result
in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To
be certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local Telephone Company. For
products approved after July 23, 2001, the REN for this product is part of
the product identifier that has the format. US: AAAEQ##TXXXX. The
digits represented by ## are the REN without a decimal point (e.g., 03 is a
REN of 0.3). For earlier products, the REN is separately shown on the
label.
Incidence of Harm
If this equipment TL405LE-LAT causes harm to the telephone network,
the telephone company will notify you in advance that temporary discon-
tinuance of service may be required. But if advance notice is not practical,
the Telephone Company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment.
If this happens the Telephone Company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted
service.
Equipment Maintenance Facility
If trouble is experienced with this equipment for repair or warranty infor-
mation, please contact the facility indicated below. If the equipment is
causing harm to the telephone network, the Telephone Company may
request that you disconnect the equipment until the problem is solved. This
equipment is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation com-
mission for information.
Alarm dialling equipment must be able to seize the telephone line and
place a call in an emergency situation. It must be able to do this even if
other equipment (telephone, answering system, computer modem, etc.)
already has the telephone line in use. To do so, alarm dialling equipment
must be connected to a properly installed RJ-31X jack that is electrically in
series with and ahead of all other equipment attached to the same telephone
line.
Proper installation is depicted in the figure below. If you have any ques-
tions concerning these instructions, you should consult your telephone
company or a qualified installer about installing the RJ-31X jack and alarm
dialling equipment for you.
93