Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TC-BD 500 Manual De Instrucciones Original

6.9 Working speeds
Ensure that you drill at the proper speed. Drill
speed is dependent on the diameter of the drill bit
and its material.
The table below acts as a guide for selecting the
proper speed for drill bits made of various mate-
rials.
The rotational speeds shown are merely sugges-
ted values.
Ø Drill bit Cast iron Steel
3 2550 1600
4 1900 1200
5 1530 955
6 1270 800
7 1090 680
8 960 600
9 850 530
10 70,85 480
11 700 435
12 640 400
13 590 370
14 545 340
16 480 300
18 425 265
20 380 240
22 350 220
25 305 190
6.10 Countersinking and center-drilling
With this bench drill you can also perform coun-
tersinking and center-drilling jobs. Please note:
Countersinking should be performed at the lowest
speed, while a high speed is required for center-
drilling.
6.11 Woodworking
Wood dust can be a health hazard! Be sure to use
a suitable dust extractor when working with wood.
It is imperative to wear a suitable dust mask when
performing any work that generates dust.
6.12 Replacing the V-belt (Fig. 12/14-16)
The V-belt of the pillar drill can be replaced if it
becomes worn. Proceed as described in section
6.4 Speed settings.
In this case replace the V-belt (26) instead of re-
positioning it.
Anl_TC_BD_500_SPK13.indb 21 Anl_TC_BD_500_SPK13.indb 21
GB

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
Iron Aluminium Bronze
Danger!
2230 9500 8000
1680 7200 6000 Always pull out the mains power plug before star-
1340 5700 4800
ting any cleaning work.
1100 4800 4000
960 4100 3400
8.1 Cleaning
•
840 3600 3000
740 3200 2650
670 2860 2400
610 2600 2170
560 2400 2000
515 2200 1840
480 2000 1700
420 1800 1500
370 1600 1300
335 1400 1200
305 1300 1100
270 1150 950
•
•
- 21 -
ordering of spare parts
The pillar drill is maintenance-free to a large
extent. Keep the equipment clean. Pull out
the power plug before doing any cleaning and
maintenance work on the equipment. Do not
use any harsh, abrasive solvents for cleaning
purposes. Make sure that no liquid gets into
the equipment. Re-grease all bare parts when
the work is finished. Particularly the drill pillar,
blank parts of the column, and the drill table
should be re-greased at regular intervals. Use
a standard, acid-free lubricating grease for
this purpose.
Note: Do not dispose of oil-soaked rags,
grease-soaked rags, oil residues and grease
residues in your household rubbish. Dispose
of such materials in an environment-friendly
way. Check and clean the ventilation holes
regularly. Store the equipment in a dry room.
If the equipment becomes damaged, do not
try to repair it yourself. Leave such repairs to a
qualifi ed electrician.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
16.12.2020 10:04:55 16.12.2020 10:04:55