Remote Control - REVELL SKY FUN Manual Del Usuario

1 helICOPTer
1A Counter-rotating 1D LED lamps
rotor blades
1E Charge socket
1B Stabiliser
1F ON/OFF switch
1C Tail rotor
3 InserTIng BaTTerIes (reMOTe COnTrOl)
3A Unscrew and 3B Insert 6 x 1.5 V AA batteries
remove the and pay attention to the polarity,
cover as shown in the battery
compartment.
4 ChargIng The helICOPTer
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
1. Switch off the helicopter and the remote control.
2. Plug the USB charger into a USB hub or a USB port on a computer. (4A).
If the charger is ready for operation, the LED on the top illuminates red.
3. Now insert the plug of the charger on the bottom side of the model (4B).
The charging process begins automatically.
4. The Power LED on the charger goes out during the charging process and illuminates
red when the battery is full (4C). After charging, disconnect the battery from the
charger and pull the charger plug out of the USB interface.
The helicopter can fly for approx. 6-8 minutes after a charge time of
approx. 40 minutes.
Warning notice: The LiPo battery does not normally heat up while charging. If it
should become warm or even hot and/or changes to the surface begin to appear,
immediately discontinue the charging process!
You can also charge your helicopter with the remote control:
• Switch off the remote control and the helicopter.
• The plug for the charge cable is located on the back of the remote control (4D).
Remove the cover and then carefully plug the cable into the charge socket of the
helicopter (4E). The plug must be gently inserted into the charging socket – DO NOT
USE FORCE. If the plug is not correctly inserted into the charging socket, the helicopter
may become damaged and, under certain circumstances, become an injury risk.
Switch on the remote; the power LED blinks red. Slowly move the thrust controller to
maximum and then back to its starting position to activate the remote control (2B);
the power LED will begin to blink quickly. This process lasts for approx. 3 seconds.
Now the LED continuously illuminates green.
• The charging process is complete as soon as the LED is illuminated red.
• After the charging process, switch the power switch to "OFF" and disconnect the
charge cable from the helicopter.
14

2 reMOTe COnTrOl

2A ON/OFF switch 2E Controller for
forwards and
2B Thrust controller
backwards flight
2C Antenna
as well as rotation
2D Left/right trim
2F ON/OFF button
adjustment
for LEDs
3C Close the battery
cover and secure
with the screw.
5 sTarT PreParaTIOn
The thrust controller (the left controller on the remote control) must point down before
being switched on (5A). Then set the remote control's ON/OFF switch to "ON" (5B).
The power LED begins to blink.
Now set the helicopter's ON/OFF switch to the "ON" (5C). Place the helicopter on the
ground so that the tail points toward you (5D).
Activate the remote control by slowly moving the thrust controller to maximum and
then back to its starting position; the power LED will begin to blink quickly. This process
lasts for approx. 3 seconds. The helicopter is ready to start when the headlamp is
permanently illuminated red.
6 TrIM aDJusTMenT OF The COnTrOl
The correct trimming is a basic requirement for achieving fault-free flying from the
helicopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the helicopter approximately 0.5 to 1 metre in altitude.
6A If the helicopter quickly or slowly rotates clockwise by itself...
If the helicopter begins to automatically rotate clockwise, rotate the left/right trim
adjustment anti-clockwise until the helicopter no longer rotates on its own.
6B If the helicopter quickly or slowly rotates anti-clockwise by itself...
If the helicopter begins to automatically rotate anti-clockwise, rotate the left/right trim
adjustment clockwise until the helicopter no longer rotates on its own.
7 FlIghT COnTrOl
Note: Only minimal corrections of the controls are necessary for a smoothing flying
behaviour of the helicopter!
7A Take off or increase altitude by
carefully moving the control for thrust
forward.
7C Fly forward by moving the controller
for forward/backward flight and right/
left rotation carefully forward.
7E Turn the helicopter around anti-
clockwise by moving the controller for
forward/backward flight and right/left
rotation to the left.
7B Land or decrease altitude by moving
the control for thrust backward. Only
minimal corrections to the controller are
necessary to ensure smoothing flying of
the helicopter!
7D Fly backward by moving the controller
for forward/backward flight and right/left
rotation carefully backward.
7F Turn the helicopter around clockwise
by moving the controller for forward/
backward flight and right/left rotation to
the right.
15