Starting setup
The Setup Wizard appears the first time you turn on the TV,
and assists you to specify the Air/Cable setting, and program
your channels automatically.
IMPORTANT: Make sure that the antenna or cable TV system
connection is made.
1
To turn on the TV, press POWER. (It may take approx. 10
seconds for a picture to appear on screen.) The Initial Setup
Wizard begins.
2
Select your "TV Mode" by pressing ▲ or ▼ to select "Home"
or "Retail". This product qualifies for ENERGY STAR in Home
mode with its default settings.
NOTE:
Retail mode is intended for in-store display and resets video
settings each time TV is turned on.
3
Press ▶ to go to the next step.
4
Press ▲ or ▼ to your desired language, then press ▶ to go to
the next step.
5
Press ▲ or ▼ to select your time zone, then press ▶.
• In the rare event that you live within broadcast range of two
stations in two different time zones, the TV may recognize
the wrong station for the auto clock set.
6
Press ▲ or ▼ to your desired time format, then press ▶.
7
Press ▲ or ▼ to select signal type that you using, then press
▶.
8
Auto Channel Scan will begin. After the scan is completed,
a TV channel appears on the screen.
• Depending on the reception condition, it may take up to 30
minutes to complete scanning channels. Please allow the
process to complete without interruption.
NOTE:
• If you press EXIT during the "Auto Channel Scan" process, the
Auto Channel Scan will stop and the TV will change to the normal
view.
• When you make a menu selection, your changes occur
immediately. You do not have to press EXIT to see your changes.
TV operation
1
To turn on the TV, press POWER. (It may take approx.10
seconds for a picture to appear on screen.)
2
Adjust the volume level by pressing VOL (VOLUME) + or – .
The volume level will be indicated on the screen by a volume
bar.
If the volume increases, the number of bars also increases.
If the volume decreases, the number of bars also decreases.
3
Set the Source option to the appropriate selection (see "Air/
Cable selection" on page 18).
4
Press the Direct Channel Selection Buttons (0-9, –) to
select the channel.
TO SELECT ANALOG CHANNELS
1-9:
Press 1-9 as needed. Example, to select channel 2,
press 2, then press SELECT..
10-99:
Press the 2 digits in order. Example, to select
channel 12, press 1, 2, then press SELECT.
100-135: Press the 3 digits in order. Example, to select
channel 120, press 1, 2, 0, then press SELECT.
TO SELECT DIGITAL CHANNELS
Press the first digits, then press the – button followed by the
remaining number.
Example: To select channel 15-1, press 1, 5, –, 1, then press
SELECT.
• If a channel is selected with only audio content, "Audio Only"
will be displayed on the screen.
• If a channel is selected with a weak digital signal, "Weak or
No Signal" will be displayed on the screen.
• The same program may be available on either an analog
channel or a digital channel. You may choose to watch
either format.
VHF/UHF/CABLE CHANNELS
Air
VHF
2-13
UHF
STD/HRC/IRC
14-69
14-36
37-59
60-85
86-94
95-99
100-135
01
NOTE:
• If a channel with no broadcast is selected, the sound will
automatically be muted.
• It may take a few seconds for a digital channel picture to appear
on screen after being selected.
To select the video input source
To view a signal from another device connected to your TV, such
as a VCR player, press INPUT, then press ▲ or ▼ to select the
desired input, then press SELECT.
Cable
VHF
2-13
(A) (W)
(AA) (WW)
(AAA) (ZZZ)
(86) (94)
(A-5) (A-1)
(100) (135)
(4A)
13 EN