Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE: Two people are recommended to assemble this unit.
1. PLACE the rear CMS
®
(Cable Management System) post (3) upright with the
shelf slot facing toward the front.
2. ALIGN the two holes on the CMS
matching holes toward the rear bottom of the left side frame (1).
SECURE the side frame (1) to the CMS
DO NOT FULLY TIGHTEN THE SCREWS AT THIS POINT.
3. INSERT the round shelf support bars (4) into left side frame leg (1) holes with the
cut-out slots on both ends facing DOWNWARD. PUSH downward on the bars until the
slot snaps into the side frame.
4. INSERT the upper front support bar (5) into the cut-outs located on the inside
top of the left side frame (1) with the cut-out slots on the upper front
support bar facing down.
NOTE: When positioned correctly, the cut-out slot in the
upper front support bar will fit over the inner edge of each
side frame with the bar ends inside the top of the frame.
5. REPEAT steps B and C for the right side frame (2). DO
NOT FULLY TIGHTEN THE SCREWS AT THIS POINT.
6. PLACE the small glass pads (7) onto the lower rear glass
support bar of the CMS
®
post (3). PLACE the larger and taller
glass pads (8) onto the upper rear glass support bar of the
CMS
®
post (3) and front upper glass support bars.
7. MOVE the assembled stand to the location it will
occupy in the room BEFORE adding the glass
shelves, TV, or other equipment.
8. SLIDE the bottom (middle sized) shelf (9) into
the cut-out slot on the CMS
secure tightly into the shelf clips (11) with
the set screws (13) and plastic screwdriver.
NOTE: You cannot place the shelves into
position unless the support bars (4) are
securely snapped into place.
9. SLIDE the center (smallest sized) shelf (10) into the cut-out
slot on the CMS
®
post (3) , and secure tightly into the shelf clips
(11) with the set screws (13) and plastic screwdriver.
10. GO BACK AND TIGHTEN the screws to secure the side frames (1)
and (2) and the CMS
®
post bar (3).
11. PLACE the top (largest sized) shelf (12) onto the rear support bar
and top of the CMS
®
post (3) with the top extended out exactly 2.5"
from the end of CMS
®
post (3), as shown in Fig. 4.
IMPORTANT: REMOVE ALL GLASS, TV AND OTHER EQUIPMENT
FROM THE STAND PRIOR TO MOVING THE ASSEMBLED UNIT. DO
NOT ATTEMPT TO MOVE THE ASSEMBLED STAND AFTER THE GLASS
SHELVES HAVE BEEN INSTALLED, AND/OR WHEN THERE IS
EQUIPMENT LOCATED ON THE STAND AS THIS MAY CAUSE THE
SHELVES TO BECOME UNSECURE AND FALL. MAKE SURE THAT THE FRONT OF THE TV IS
POSITIONED A FEW INCHES BACK FROM THE FRONT OF THE TOP GLASS. WHEN IN USE,
THIS FURNITURE MUST BE PLACED ON A FLAT AND LEVEL SURFACE.ALWAYS PLACE THE
HEAVIEST EQUIPMENT ON THE BOTTOM SHELF.
English
4
®
post lower rear support bar end with the
®
post bar (3) with two screws (6).
®
post (3), and
6
1 x
1 x
Philips Screwdriver
2 x
12
8
8
3
8
7
4
9
fig. 1
1
2.5"
fig. 4
Part #:
Ordering part #
CMPT 006
5 x
Item #:
Sheet nr.
Allen Wrench
Part #:
Ordering part #
CMPT 004
4 x
Item #:
Sheet nr.
Part #:
Ordering part #
PDPL 021
8 x
Item #:
Item #
7
8
8
5
6
11
10
fig. 2
fig. 5
Part #:
Ordering part #
PDPL 029
Item #:
Item #
8
Part #:
Ordering part #
VTAC 078
Item #:
Item #
6
Part #:
Ordering part #
VTPL 001
Item #:
Item #
13
13
fig. 3
2
Publicidad
