Lutron PowPak RMJS-CCO1-24-B Manual De Installation

PowPak | Installation
CCO Module
Part of the Vive Family
24 V~ 45 mA
RMJS-CCO1-24-B
NEC
24 V- 35 mA ®
URMJS-CCO1-24B
UL 2043 Plenum Rated
Note for Replacement:
RMxS and URMxS - the "S" model can replace the non-"S" model
Important Notes:
Please read before installing.
• For installation by a qualified electrician in accordance with all local and
national electrical codes.
• Note: Use copper conductors only.
• Check to see that the device type and rating is suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely
before installation.
• Operate between 32 °F (0 °C) and 131 °F (55 °C).
• 0% to 90% humidity, non-condensing.
• For indoor use only.
WARNING
Shock Hazard. May result in serious injury or death.
Turn off power at circuit breaker before installing the unit.
PowPak
CCO Module
Install in center of room to
maximize RF coverage.
Radio Powr Savr
Occupancy Sensor
30 ft (9 m)
Maximum
Pico
Remote
Control
40 ft (12 m)
All Wireless Transmitters must be installed within
30 ft (9 m) of the PowPak CCO Module.
PowPak | Programming Without a Vive Hub
1
Associate Wireless Transmitters to PowPak CCO Module
Before beginning this step, make sure that there are no other PowPak modules being set up within the same building. It is possible that Wireless Transmitters from
other systems can be incorrectly associated to this system.
A
Hold the CCO Toggle
button on the PowPak
CCO
CCO Module for 6 seconds
Toggle
to enter association mode.
Advanced
Note: The load will flash Operations
once after each step
to confirm successful
completion.
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Required Components
For each system ensure you have:
At least one PowPak CCO Module
041669
Rev. A
07/2018 Load
Status
CLASS 2 LED
CCO Toggle
+
Advanced
Operations
Contact
Closure
Output
(CCO)
(Class 2)
PowPak CCO Module
Start Here
1
Install PowPak CCO Module
Suggested Installation Location: Center of room to ensure
proper RF coverage of area.
When installing a PowPak CCO Module,
use the supplied conduit nut and wire the module
as shown.
Note: PowPak CCO Module may also be
mounted on or inside a junction box.
If installing unit inside a junction box please
see Application Note #423.
For more information:
www.lutron.com/powpakcco
2
Programming with a Vive Hub
A Use an iOS or Android B Download the Lutron
® ®
compatible device. Vive app.
Vive
B
Hold the indicated button
on a Wireless Transmitter
for 6 seconds to
associate the device.*
Repeat for any additional
Wireless Transmitters.
* If no g button, hold
"Lights Off" button.
Lutron, Pico, and PowPak are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. Radio Powr Savr and Vive are trademarks of Lutron Electronics Co., Inc. iOS is a registered trademark of Cisco in the U.S. and other countries and is used under license.
Google is a registered trademark and Android and Chrome are trademarks of Google Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. ©2013 – 2018 Lutron Electronics Co., Inc.
At least one Wireless Transmitter
Pico
Remote Control
(10 maximum)
Radio Powr Savr
Daylight Sensor
Radio Powr Savr Occupancy
Link Cal.
Test
(1 maximum)
Sensor (10 maximum)
Supply Voltage
24 V~ / 24 V-
Wire nut
(2 Supplied)
COM
(Common)
NO
NC
(Normally Open)
(Normally Closed)
C Open the app and
follow the instructions.
vive.lutron.com
C
Hold the CCO Toggle button on the
PowPak CCO Module for 6 seconds
to save association(s).
D Permanently install wireless transmitters
(consult individual component installation
guides for information).
Link
Test
Customer Assistance
Limited Warranty: www.lutron.com/TechnicalDocumentLibrary/369-119_Wallbox_Warranty.pdf
FCC / IC Information
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Customer Assistance | 1.844.LUTRON1 U.S.A., Canada, and the Caribbean | +44.(0)20.7680.4481 Europe | +1.610.282.3800 Others | www.lutron.com/support
Note: CCO Module supply wires can be
connected in any polarity.
Mounting screw
(2 Supplied)
To CCO-controlled device
Note: When wiring CCO output,
use 20 AWG to 16 AWG
2 2
(0.5 mm to 1.5 mm ) solid or stranded wire.
Note: For further information on set up, programming,
and troubleshooting with a Vive system, please refer to the
installation instructions included with the Vive hub or visit
www.lutron.com/vive
Note: For programming the PowPak CCO Module
without a Vive hub see Programming Without a Vive
Hub below.
2
Calibrate the Radio Powr Savr
Daylight Sensor
Daylight Sensor will control all wired fixtures equally.
A
Press and release the "Cal." button on the
Daylight Sensor.
B
Turn lights in room on using the CCO Toggle
button on the PowPak CCO Module or an
Link
associated Pico remote control. Test
C
Press and hold the "Cal." button for 6 seconds.
D Exit room for 5 minutes to allow calibration to be completed.
Note: When calibration has completed, all lights will flash and
begin to respond to daylight.
www.lutron.com/support
CCO Information
• This product features a single contact closure output with both
normally open (NO) and normally closed (NC) dry contacts.
• The CCO incorporates maintained output behavior only.
• The CCO is rated to switch resistive loads at
Switching Resistive
voltages up to 24 V only. To properly control
Voltage Load
R
inductive load types such as relays, solenoids,
0-24 V- 1.0 A
or motors, refer to Application Note #434.
0-24 V~ 0.5 A
Transmitting Device Transmitted Command CCO Default Action
Pico On NO = Close, NC = Open
Remote Control
Off NO = Open, NC = Close
Raise No Action
Lower No Action
Preset NO = Close, NC = Open
Radio Powr Savr Occupied NO = Close, NC = Open
Occupancy Sensor
Unoccupied NO = Open, NC = Close
Radio Powr Savr Occupied No Action
Vacancy Sensor
Unoccupied NO = Open, NC = Close
Radio Powr Savr Ambient light below target NO = Close, NC = Open
Daylight Sensor level
Ambient light above target NO = Open, NC = Close
level
Reset Factory Defaults
Note: In some instances it may be necessary to reset the PowPak
CCO Module back to factory default settings.
A Rapidly tap the Advanced Operations (ADV) button on the CCO
module 3 times and hold on the fourth time until the LED begins to
flash at a rate of approximately 2 blinks every 1 second, then release
the ADV button.
B Within 3 seconds of the start of flashing of the LED on the CCO
module, rapidly tap the ADV button on the CCO module 3 times
again. Make sure to release the ADV button after the third press.
C The LED will flash at a rate of 2 blinks every 3 seconds to indicate the
unit has been reset to factory defaults.
Note: Any associations or programming previously set up with the
unit will be lost and will need to be re-programmed.
Troubleshooting
www.lutron.com
CCO-controlled • Ensure breaker to the PowPak CCO Module is on.
device does • Ensure the CCO-controlled device has been
not respond properly wired to the PowPak CCO Module.
to Wireless • Ensure Wireless Transmitter is properly associated
Transmitter(s) to PowPak CCO Module.
Cal.
• Ensure Wireless Transmitter's battery is installed
correctly.
Wireless • The maximum number of Wireless Transmitters
Transmitter(s) have been associated to the PowPak CCO
cannot be Module. To remove a previously set up Wireless
associated to Transmitter, tap the button used for association on
PowPak CCO the Wireless Transmitter three times, on the third
Module tap hold for three seconds and then tap three more
times.