water used for the baby's bath must be
between 35 ° and 38 °.
• This bath seat can be used alone or on the
stand until the child tries to get up on his
own.
• Always check the attachment and stabili-
ty of the bath seat on the stand.
LIST OF COMPONENTS
A - Tub/Seat
A1 - T-Bar
A2 - Extractable leg
A3 - Extractable leg suction cups (2x)
A4 - Front suction cups (2x)
A5 - Plug
A6 - Lower T-Bar release tab
A7 - Lower T-Bar slot
A8 - Stand housing slots
A9 - Side T-Bar release buttons
A10 - Release buttons
A11 - Central T-Bar slot
A12 - Side T-Bar slots
B - Upper stand
B1- Joints
B2 - Joint buttons
B3 - Stand inserts
B4 - Upper legs
C - Lower legs (4x)
MAINTENANCE
This product requires periodical maintenance. Cleaning
and maintenance operations must be performed exclu-
sively by an adult.
CLEANING
Periodically wipe the plastic parts clean with a soft
damp cloth. Dry the metal parts after contact with wa-
ter to prevent rust from forming. Do not use solvents or
abrasive products for cleaning.
0 – 6m USE WITH THE STAND
1. Insert lower legs "C" in upper legs "B4", putting light
pressure on the pins found on the ends of the lower
legs until you hear the locking click (Fig.1).
2. Open upper stand "B", moving the front legs away
from the rear legs (Fig.2).
3. Remove T-Bar "A1" installed under tub/seat "A", press-
ing on lower release tab "7"(Fig.3).
4. Insert T-Bar "A1" in the central slot "A11" then in side
slot "A12" (Fig.4), putting light pressure on the bottom
until you hear a locking click (Fig.4A).
5. Place tub/seat "A" on upper stand "B", inserting stand
inserts "B3" inside slot housings "A8" located on tub/
seat "A" until you hear a locking click (Fig.5).
6. Ensure you line up the symbols positioned on the
side wall and on the joints, as shown in figure 6.
7. After using the product, remove plug "A5" to empty
the tub (Fig.7).
6 -12m USE WITH THE STAND
8. Release tub/seat "A" from stand "B", pressing buttons
"B3" and turning tub/seat "A" 180°. Place tub/seat "A"
on upper stand "B", inserting stand inserts "B3" inside
slot housings "A8" located on tub/seat "A" until you
hear a locking click (Fig.8).
The symbols positioned on the side wall and on the
joints can be seen, as shown in figure 6.
Before using the product, remove plug "A5", unscrewing
it from the bottom (Fig.7).
0 – 6m USE IN THE BATHTUB
9. If tub/seat "A" has been installed on the stand, you
need to release it from stand "B" by pressing on but-
tons "A10" (Fig.9).
10. Remove T-Bar "A1", pressing on side buttons "A9" then
pressing on lower tab "A6" (Fig.10).
11. Insert T-Bar "A1" in the lower part of tub/seat "A", en-
suring that it has been properly engaged inside low-
er slot "A7" (Fig.11).
After using the product, remove plug "A5" to empty the
tub (Fig.7).
6 -12m USE IN THE BATHTUB
12. If tub/seat "A" has been installed on the stand, you
need to release it from stand "B" by pressing on but-
tons "A10" (Fig.12).
13. Verify that the T-Bar has been properly inserted in
slots "A11" and "A12" (Fig.13).
14. Activate extractable leg "A2" by pulling it towards
the front of tub/seat "A" and turning it towards the
rear until you hear a locking click (Fig.14).
Before using the product, remove plug "A5", unscrewing
it from the bottom (Fig.7).
WARNING:
15. Verify that the 4 suction cups "A3" and "A4" adhere
perfectly to the surface of the bathtub (Fig. 15).
CLOSURE
16. The product can be closed by pressing joint buttons
"B2" and bringing the front and rear legs together
(Fig.16).
WARRANTY
The product is guaranteed against any conformity de-
fect in normal conditions of use as provided for by the
instructions.
The warranty shall not therefore apply in the case of dam-
age caused by improper use, wear or accidental events.
For the duration of the warranty on conformity defects
please refer to the specific provisions of applicable na-
tional laws in the country of purchase, where appropriate.
9