Descargar Imprimir esta página

Matco Tools MT1874 Instrucciones De Operación página 2

Publicidad

Idiomas disponibles

Idiomas disponibles

FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
THIS INSTRUCTION MANUAL CONTAINS
IMPORTANT SAFETY INFORMATION.
READ THIS INSTRUCTION MANUAL CAREFULLY
AND UNDERSTAND ALL INFORMATION BEFORE
OPERATING THIS TOOL.
• Always operate, inspect and maintain this tool in
accordance
Institute Safety Code of Portable Air Tools (ANSI
B186.1)
and
and regulations.
• For safety, top performance and maximum durability
of parts, operate this tool at 90 psig 6.2 bar max
air pressure with 3/8" diameter air supply hose.
• Always
wear
protection
maintenance on this tool.
• Always wear hearing protection when using this
tool. High sound levels can cause permanent hearing
loss. Use hearing protection as recommended by
your employer or OSHA regulation.
• Keep the tool in efficient operating condition.
• Operators
physically able to handle the bulk, weight and
power of this tool.
• Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to your
hands and arms. Discontinue use of tool if discomfort,
tingling feeling or pain occurs. Seek medical advice
before resuming use.
• Air under pressure can cause severe injury. Never
direct air at yourself or others. Always turn off the
air supply, drain hose of air pressure and detach tool
from
air
adjusting any accessory on this tool, or before
performing any maintenance on this tool. Failure to
do so could result in injury. Whip hoses can cause
serious injury. Always check for damaged, frayed
or loose hoses and fittings, and replace immediately.
Do not use quick detach couplings at tool. See
instructions for correct set-up.
OPERATION
The air regulator knob can be used as an air throttle and can be used for
setting positive speed control. The air inlet used for connecting air supply has
standard 1/4" NPT thread.
Let the sander do the work. The normal weight of the machine is sufficient
for efficient sanding. Do not put additional pressure on the machine. This will
only slow down the speed of the pad, reduce sanding efficiency and put an
additional burden on the motor. Start the sander off the work, set it down on
the work evenly and move it slowly back and forth in wide, overlapping areas.
When finished sanding, lift it off the work before stopping the motor.
MT1874
MT1874_011206_OpMan.indd 2
MT1874 6" Heavy Duty DA Sander
with
American
National
any
other
applicable
safety
impact-resistant
eye
and
when
operating
or
performing
and
maintenance
personnel
supply
before
installing,
removing
• Place the tool on the work before starting the tool.
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
Standards
not overreach when operating the tool.
• Anticipate and be alert for sudden changes in motion
codes
during start up and operation of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Tool shaft may continue to rotate briefly after throttle
is released. Avoid direct contact with accessories
face
during and after use. Gloves will reduce the risk of cuts or
burns.
• Keep away from rotating end of tool. Do not
wear jewelry or loose clothing. Secure long hair.
Scalping can occur if hair is not kept away from
tool and accessories.
Choking can occur if neckwear is not kept away
from tool and accessories.
must
be
• Never mount a grinding wheel on a sander. A
grinding wheel that bursts can cause very serious
injury
guarded. Inspect
Do not use if cracked or damaged.
• Avoid direct contact with moving sanding pad to
prevent pinching or cutting of hands or other body
parts.
• Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
or
2
or
death
when
not
backing
pad
before
Rev. 01/12/06
properly
each
use.
1/12/06 2:41:41 PM

Publicidad

loading