Amana Clean Filtr Guía De Consulta Rápida

CLEAN FILTR CLEAN FILTR CLEAN FILTR
CLEAN FILTR CLEAN FILTR
CLEAN FILTR
This oven displays
user defined intervals. When the
message displays Amana
recommends cleaning the air filter
thoroughly. Cleaning the air filter
will not shut off the message. The
message will stop displaying
automatically after 24 hours.
Depending on microwave use and
environmental conditions, the filter
may need to be cleaned more
frequently. Once the frequency is
determined, set the option for the
appropriate time frame.
Preprogrammed
Pads
To cook food using
preprogrammed cooking sequences.
1. Open oven door and place food
in oven. Close door.
2. Press desired pad.
3. Oven begins to cook.
4. At end of cooking cycle oven
beeps and shuts off.
X2 Programming
(some models)
To change the cooking factor:
1. Open oven door.
2. Press and hold pad 1 for
approximately 5 seconds.
3. Press pad to be reprogrammed.
4. Press the X2 pad.
5. Press a numbered pad to
change the cooking factor.
• Cooking factor can be set
from 10% to 100%.
• Default is 80%.
• Pad 5 would change the
cooking factor to 50%.
6. Press START pad to save
changes.
The switching operation of this microwave oven can cause voltage fluctuations on the supply line. The operation of this oven under unfavorable voltage supply
conditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissable system impedance
Zmax of 0.31 Ohms at the interface point of the user's supply. The user has to ensure that this device is connected only to a power supply system which fulfills
the requirement above. If necessary, the user can ask the public power supply company for the system impedance at the interface point.
Quick Start Reference Guide
Refer to Product Safety Manual for Safety Statements
at
A
A
So...how do I use it?
Manual Operation
To cook food using a specific entered time and power level.
1. Open oven door and place food in oven. Close door.
2. Press TIME ENTRY pad and enter cooking time.
3. Press POWER LEVEL pad to program level of microwave power if desired.
• For a lower microwave power, press pads 1 (for 10%),
through 9 (for 90%), or 0 for no microwave energy.
4. If stage cooking is desired, press TIME ENTRY pad and repeat steps
2 through 4.
5. Press START pad.
6. At end of cooking cycle oven beeps and shuts off.
Programming Items
1. Open oven door.
2. Press and hold pad 1 for approximately 5 seconds.
3. Press pad to be reprogrammed.
4. Enter cooking time by using the number pads.
5. Press POWER LEVEL pad to program level of microwave power if desired.
• For a lower microwave power, press pads 1 (for 10%),
through 9 (for 90%), or 0 for no microwave energy.
6. Press TIME ENTRY pad to add up to four additional cooking stages.
• Total cooking time cannot exceed 60 minutes.
• Enter cook time and power level as in steps 4 and 5.
7. Press START pad to set new programming changes to the pad.
NOTE: To discard changes, press STOP/RESET pad or close oven door.
X2 Pad (some models)
1. Open oven door and place food in oven. Close door.
2. Press X2 pad.
3. Press desired preprogrammed pad or pad sequence.
4. Oven begins cooking. Displayed cooking time is the total of original
cooking time and added X2 time.
Complete Owner's Manual available online
Oven Clearances
A—Allow at least 7" (17.8 cm) of clearance
around top and sides of oven. Proper air flow
around oven cools electrical components.
With restricted air flow, oven may not operate
B
properly and life of electrical parts is reduced.
B—Allow at least 2
discharge on back of oven and back wall.
9
/ " (6.5 cm) between air
16