Sony MDR-ZX750BN Guía De Referencia

Wireless
Reference Guide
Noise Canceling
Guide de référence
Stereo Headset
Guía de referencia
Casque stéréo
sans fil réducteur
de bruits
Auriculares estéreo
inalámbricos con
función de
supresión de ruido
MDR-ZX750BN
©2014 Sony Corporation Printed in Malaysia
http://www.sony.net/
English
WARNING
To reduce the risk of electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Information
FOR UNITED STATES CUSTOMERS. NOT APPLICABLE IN CANADA,
INCLUDING IN THE PROVINCE OF QUEBEC.
POUR LES CONSOMMATEURS AUX ÉTATS-UNIS. NON APPLICABLE AU
CANADA, Y COMPRIS LA PROVINCE DE QUÉBEC.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
You are cautioned that any changes or modifications not expressly approved in
this manual could void your authority to operate this equipment.
This equipment must not be co-located or operated in conjunction with any other
antenna or transmitter.
Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
ē Reorient or relocate the receiving antenna.
ē Increase the separation between the equipment and receiver.
ē Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
ē Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment
has very low levels of RF energy that are deemed to comply without testing of
specific absorption ratio (SAR).
The BluETOOTH word mark and logos are owned by the Bluetooth SIG, Inc. and any
use of such marks by Sony Corporation is under license.
The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the united
States and in other countries.
Microsoft, Windows and Windows Vista are registered trademarks or trademarks of
Microsoft Corporation in the united States and/or other countries.
Macintosh and Mac OS are trademarks of Apple Inc., registered in the u.S. and other
countries.
®
The aptX mark and the aptX logo are trade marks of CSR plc or one of its group
companies and may be registered in one or more jurisdictions.
Other trademarks and trade names are those of their respective owners.
Precautions
On BLUETOOTH communication
ˎ BluETOOTH wireless technology operates within a range of about 10 meters
(30 feet). Maximum communication range may vary depending on obstacles
(human body, metal, wall, etc.) or electromagnetic environment.
ˎ The antenna is built into the unit as illustrated in the dotted line. The sensitivity of
the BluETOOTH communication will improve by turning the direction of the built-in
antenna to the connected BluETOOTH device. The communication distance
shortens when the obstacles are between the antenna of the connected device
and this unit.
Location of
built-in
antenna
ˎ The following conditions may affect the sensitivity of BluETOOTH communication.
ē There is an obstacle such as a human body, metal, or wall between this unit and
BluETOOTH device.
ē A device using 2.4 GHz frequency, such as a wireless lAN device, cordless
telephone, or microwave oven, is in use near this unit.
ˎ Because BluETOOTH devices and wireless lAN (IEEE802.11b/g) use the same
frequency, microwave interference may occur and resulting in communication
speed deterioration, noise, or invalid connection if this unit is used near a wireless
lAN device. In such a case, perform the following.
ē use this unit at least 10 m (30 ft) away from the wireless lAN device.
ē If this unit is used within 10 m (30 ft) of a wireless lAN device, turn off the
wireless lAN device.
ē Install this unit and BluETOOTH device as near to each other as possible.
4-479-126-12(1)
ˎ Microwaves emitting from a BluETOOTH device may affect the operation of
electronic medical devices. Turn off this unit and other BluETOOTH devices in the
following locations, as it may cause an accident:
ē where inflammable gas is present, in a hospital, train, airplane, or a petrol station
ē near automatic doors or a fire alarm
ˎ This unit supports security capabilities that comply with the BluETOOTH standard
to provide a secure connection when the BluETOOTH wireless technology is used,
but security may not be enough depending on the setting. Be careful when
communicating using BluETOOTH wireless technology.
ˎ We do not take any responsibility for the leakage of information during
uS
BluETOOTH communication.
ˎ Connection with all BluETOOTH devices cannot be guaranteed.
ē A device featuring BluETOOTH function is required to conform to the
FR
BluETOOTH standard specified by Bluetooth SIG, Inc. and be authenticated.
ē Even if the connected device conforms to the above mentioned BluETOOTH
ES
standard, some devices may not be connected or work correctly, depending on
the features or specifications of the device.
ē While talking on the phone hands free, noise may occur, depending on the
device or communication environment.
ˎ Depending on the device to be connected, it may require some time to start
communication.
If you cannot operate the unit
ˎ Reset the unit.
Insert a small pin, etc., into the hole, and push it until you feel a click. Pairing
information is not deleted.
ˎ If you are still unable to operate the unit even after the resetting operation above,
initialize the unit as follows.
Turn off the unit by pressing the POWER button for more than 2 seconds. Then,
press and hold the POWER button and the
7 seconds. The indicator (blue) flashes 4 times, and the unit is reset to the factory
settings. All pairing information is deleted.
What is noise canceling?
ˎ The noise canceling circuit actually senses outside noise with built-in microphones
and sends an equal-but-opposite canceling signal to the unit.
ē The noise canceling effect may not be pronounced in a very quiet environment,
or some noise may be heard.
ē The noise canceling effect may vary depending on how you wear the unit.
ē The noise canceling function works for noise in the low frequency band primarily.
Although noise is reduced, it is not canceled completely.
ē When you use the unit in a train or a car, noise may occur depending on street
conditions.
ē Mobile phones may cause interference and noise. Should this occur, locate the
unit further away from the mobile phone.
ē Do not cover the microphones of the headphones (MIC) with your hands. The
noise canceling function may not work properly.
On charging the unit
ˎ This unit can be charged using uSB only. Personal computer with uSB port, or uSB
Charging AC Power Adaptor AC-uD11 (sold separately) is required for charging.
ˎ This unit cannot be turned on, and the BluETOOTH function and noise canceling
function cannot be used while charging.
Note on static electricity
ˎ Static electricity accumulated in the body may cause mild tingling in your ears. To
minimise the effect, wear clothes made from natural materials.
Others
ˎ Do not place this unit in a place exposed to humidity, dust, soot or steam, subject
to direct sunlight, or in a car waiting at a traffic signal. It may cause a malfunction.
ˎ using the BluETOOTH device may not function on mobile phones, depending on
radio wave conditions and location where the equipment is being used.
ˎ If you experience discomfort after using the BluETOOTH device, stop using the
BluETOOTH device immediately. Should any problem persist, consult your nearest
Sony dealer.
ˎ listening with this unit at high volume may affect your hearing. For traffic safety,
do not use this unit while driving or cycling.
ˎ Do not put weight or pressure on this unit as it may cause the unit to deform
during long storage.
ˎ Do not subject the unit to excessive shock.
ˎ Clean the unit with a soft dry cloth.
ˎ Do not expose the unit to water. The unit is not waterproof.
Remember to follow the precautions below.
ē Be careful not to drop the unit into a sink or other container filled with water.
ē Do not use the unit in humid locations or bad weather, such as in the rain or
snow.
ē Do not get the unit wet.
If you touch the unit with wet hands, or put the unit in a damp article of clothing,
the unit may get wet and this may cause a malfunction of the unit.
ˎ The earpads may deteriorate due to longterm storage or use.
ˎ If you have any questions or problems concerning this unit that are not covered in
this manual, please consult your nearest Sony dealer.
Specifications
General
Communication System: BluETOOTH Specification version 3.0
Output: BluETOOTH Specification Power Class 2
Maximum communication range: line of sight approx. 10 m (30 ft)
Frequency band: 2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Modulation method: FHSS
Compatible BLUETOOTH Profiles
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
HFP (Hands-free Profile)
HSP (Headset Profile)
Supported Codec : SBC
3)
Supported content protection method: SCMS-T
Transmission range (A2DP): 20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)
Total Noise Suppression Ratio: Approx. 17 dB
Included items:
Wireless noise canceling stereo headset (1)
Micro-uSB cable (approx. 50 cm (1.64 ft)) (1)
Connecting Cord (approx. 1.5 m (4.92 ft)) (1)
Reference Guide (this sheet) (1)
Quick Start Guide (1)
Other documents (1 set)
Recommended accessory:
uSB Charging AC Power Adaptor: AC-uD11 (sold separately)
The actual range will vary depending on factors such as obstacles between
1)
devices, magnetic fields around a microwave oven, static electricity, reception
sensitivity, antenna's performance, operating system, software application, etc.
BluETOOTH standard profiles indicate the purpose of BluETOOTH communication
2)
between devices.
Codec: Audio signal compression and conversion format
3)
4) Subband Codec
5) Advanced Audio Coding
Equivalent to approx. 98% reduction of energy of sound compared with not
6)
wearing the unit.
Wireless Noise Canceling Stereo Headset
Power source:
DC 3.7 V: Built-in lithium-ion rechargeable battery
DC 5 V: When charged using uSB
Mass: Approx. 230 g (8.11 oz)
Operating temperature: 0 °C to 40 °C (32 °F to 104 °F)
Usage hours:
When connecting via the BluETOOTH device
Music playback time:
Max. 13 hours (NC ON), Max. 19 hours (NC OFF)
Communication time:
Max. 10 hours (NC ON), Max. 12 hours (NC OFF)
Standby time:
Max. 26 hours (NC ON), Max. 150 hours (NC OFF)
When using the supplied connecting cord
Max. 24 hours (NC ON)
Note: usage hours may be shorter depending on the Codec and the conditions
of use.
Charging time:
Approx. 2.5 hours
Charging temperature: 5 °C to 35 °C (41 °F to 95 °F)
/ button together for about
MIC
1)
2) :
, AAC , aptX
4) 5)
6)
Receiver
Type: Closed, Dynamic
Driver units: 40 mm
Frequency response: 8 Hz - 22,000 Hz (when using the supplied connecting cord)
Maximum input: 100 mW (when using the supplied connecting cord)
Impedance:
NC ON: 23 Ω (1 kHz) (when using the supplied connecting cord)
NC OFF: 50 Ω (1 kHz) (when using the supplied connecting cord)
Sound pressure sensitivity:
NC ON: 102 dB/mW (when using the supplied connecting cord)
NC OFF: 101 dB/mW (when using the supplied connecting cord)
Microphone
Type: Electret condenser
Direction characteristic: Omni directional
Effective frequency range: 100 Hz - 4,000 Hz
System requirements for battery charge using
USB
Personal Computer with pre-installed with any of the following operating systems
and uSB port:
Operating Systems
(when using Windows)
® ®
Windows 8 / Windows 8 Pro
®
Windows 7
Home Basic / Home Premium / Professional / ultimate
®
Windows Vista (Service Pack 2 or later)
Home Basic / Home Premium / Business / ultimate
®
Windows XP (Service Pack 3 or later)
Home Edition / Professional / Media Center Edition 2004 / Media Center Edition 2005
(when using Macintosh)
Mac OS X (version.10.3 or later)
Design and specifications are subject to change without notice.
Français
AVERTISSEMENT
Pour éviter tout risque d'électrocution, n'ouvrez pas le coffret. Ne confiez
les réparations qu'à un technicien qualifié.
Information
le présent appareil est conforme aux CNR d'Industrie Canada applicable aux
appareils radio exempts de licence. l'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Cet équipement est conforme aux limites d'exposition aux rayonnements énoncées
pour un environnement non contrôlé et respecte les règles les radioélectriques (RF)
de la FCC lignes directrices d'exposition et d'exposition aux fréquences
radioélectriques (RF) CNR-102 de l'IC. Cet équipement émet une énergie RF très faible
qui est considérée conforme sans évaluation du débit d'absorption spécifique (DAS).
la marque de mot BluETOOTH et les logos sont la propriété de Bluetooth SIG, Inc. et
l'utilisation de ces marques par Sony Corporation est effectuée sous licence.
N Mark est une marque commerciale ou une marque déposée de NFC Forum, Inc. aux
États-unis et dans d'autres pays.
Microsoft, Windows et Windows Vista sont des marques déposées ou des marques
de commerce de Microsoft Corporation aux États-unis et/ou dans les autres pays.
Macintosh et Mac OS sont des marques de commerce de Apple Inc., déposées aux
États-unis et dans d'autres pays.
la marque aptX® et le logo aptX sont des marques commerciales de CSR plc ou
d'une des sociétés de son groupe, et ils peuvent être déposés dans une ou plusieurs
juridictions.
les autres marques commerciales et noms commerciaux appartiennent à leurs
propriétaires respectifs.
Précautions
Communication BLUETOOTH
ˎ la technologie BluETOOTH sans fil fonctionne dans un rayon d'environ 10 mètres
(30 pieds).
la portée de communication maximale peut varier en fonction des obstacles
(personnes, éléments métalliques, mur, etc.) ou de l'environnement
électromagnétique.
ˎ l'illustration ci-dessous indique l'emplacement de l'antenne intégrée sur l'appareil.
la sensibilité de la communication BluETOOTH pourra être améliorée en modifiant
l'orientation de l'antenne intégrée du périphérique BluETOOTH. la distance de
communication est réduite en cas d'obstacles présents entre l'antenne du
périphérique connecté et cet appareil.
Emplacement
de l'antenne
intégrée
ˎ les conditions suivantes peuvent affecter la sensibilité de la communication
BluETOOTH.
ē un obstacle, par exemple une personne, un objet métallique ou un mur, se
trouve entre cet appareil et le périphérique BluETOOTH.
ē un appareil utilisant une fréquence de 2,4 GHz, par exemple un périphérique
lAN sans fil, un téléphone sans fil ou un four à micro-ondes, est utilisé à
proximité de cet appareil.
ˎ Étant donné que les périphériques BluETOOTH et les périphériques lAN sans fil
(IEEE802.11b/g) utilisent la même fréquence, des interférences en hyperfréquences
peuvent survenir et entraîner une dégradation de la vitesse de communication, des
parasites ou une connexion incorrecte si cet appareil est utilisé à proximité d'un
périphérique lAN sans fil. En pareil cas, prenez les mesures suivantes.
ē utilisez cet appareil à au moins 10 mètres (30 pi) du périphérique lAN sans fil.
ē Si cet appareil est utilisé dans un rayon de 10 mètres (30 pi) par rapport au
périphérique lAN sans fil, mettez ce dernier hors tension.
ē Installez cet appareil et le périphérique BluETOOTH aussi près que possible l'un
de l'autre.
ˎ les émissions hyperfréquences d'un périphérique BluETOOTH peuvent perturber
le fonctionnement des appareils médicaux électroniques. Mettez hors tension cet
appareil et les autres périphériques BluETOOTH situés dans les endroits suivants
afin d'éviter tout accident :
ē en présence de gaz inflammable, c'est-à-dire dans un hôpital, un train, un avion
ou une station essence
ē à proximité de portes automatiques ou d'alarmes incendie
ˎ Cet appareil prend en charge les caractéristiques de sécurité conformes à la norme
BluETOOTH pour offrir une connexion sécurisée lors de l'utilisation de la
technologie sans fil BluETOOTH. Cependant, la sécurité peut être insuffisante selon
le réglage. Soyez prudent lorsque vous communiquez au moyen de la technologie
sans fil BluETOOTH.
ˎ Nous ne pouvons être tenus responsables de la fuite d'informations lors d'une
communication BluETOOTH.
ˎ la connexion ne peut pas être garantie avec tous les périphériques BluETOOTH.
ē un périphérique doté de la fonction BluETOOTH est nécessaire pour la
conformité à la norme BluETOOTH spécifiée par Bluetooth SIG Inc. et pour
l'authentification.
ē Même si le périphérique raccordé est conforme à la norme BluETOOTH
précédemment mentionnée, certains périphériques peuvent ne pas se connecter
ou ne pas fonctionner correctement, selon leurs caractéristiques ou
spécifications.
ē lors de communications téléphoniques mains libres, des parasites peuvent se
produire, selon le périphérique ou l'environnement de communication.
ˎ Selon le périphérique à connecter, le délai avant le début de la communication
peut être plus ou moins long.
Si l'appareil ne fonctionne pas
ˎ Réinitialisez l'appareil.
Insérez une petite épingle ou un objet semblable dans le trou et appuyez jusqu'à
entendre un clic. les informations de pairage ne sont pas supprimées.
ˎ Si l'appareil ne fonctionne toujours pas même après avoir été réinitialisé,
initialisez-le en suivant cette procédure.
Mettez l'appareil hors tension en appuyant sur le bouton POWER pendant plus de
2 secondes. Ensuite, maintenez le bouton POWER et le bouton
simultanément pendant environ 7 secondes. le témoin (bleu) clignote 4 fois et
l'appareil est réinitialisé à ses paramètres d'usine. Toutes les informations de
pairage sont supprimées.
/ enfoncés