Memory Function - BaBylissMEN SH500E Guia De Inicio Rapido

lets you use the appliance for approximately 3 minutes.
• When the screen displays that there are 5 minutes of use remaining ("05"), the
Timer symbol changes from orange to red and the display of the remaining
use time display fl ashes meaning that the appliance needs to be charged (by
placing the appliance in its charging stand).
USE
To start the appliance,
1
Ensure that the appliance head is perfectly clipped into place before use.
2
Press the button once.
The cutting length and approximate remaining use time are displayed.
3
Select the desired cutting length using the + and - buttons.
4
Press the button a second time.
The motor is on. You can now start using the appliance.
5
To switch the appliance off , hold down the
length is set for the next use. Press the
Note:
• The LED display screen switches off automatically after 60 seconds of disuse.
• It is possible to switch the appliance to standby mode by pressing the
once.
Tips:
- For your comfort, the appliance can be used in diff erent directions. You can make circular
movements or go backwards and forwards with the appliance over the face and neck. You
will probably need time to get used to the appliance. But quickly, using the appliance will
be comfortable and intuitive.
- If you want to go from a mid-length beard (±15 mm long) to a 3-day beard (approximately
1 mm long), it is advisable to cut it in several steps. For example: to go from a beard of
10 mm in length to one that is 1 mm long, fi rst cut to 6 mm. Then, once this fi rst stage is
complete, cut to 1mm.
- For beards that are longer than 20 mm, it is recommended that you pre-cut your beard to
about 15 mm in length before using the appliance.
- To trim your moustache or your sideburns with precision, ensure that you stretch the skin
of the area to be trimmed and only use one rotating blade.
- To shape clean and precise contours, we recommend the use of a BaByliss beard trimmer
and/or a fi nishing trimmer and/or a shaver.
CLEANING
To clean the appliance thoroughly
1
Check the appliance is on and press the Cleaning button
cleaning cycle:
The Cleaning symbol
The appliance head makes 3 back and forth movements to enable any hairs to be
button for approximately 2 seconds. The cutting
button twice to start the appliance again.
. The appliance goes into its
lights up on the LED display screen
16
eliminated more easily.
2
Gently shake the appliance above the sink to remove as much hair and residue as possible.
3
You can turn on the appliance using the
running water.
4
Place the appliance head under running water, alternating the head down and head up,
while the appliance is still running, to eff ectively remove all remaining hair. Run the tap water
over all gaps and each of the 3 head openings.
Note
• To extend the time that the appliance is cleaned under running water, you can
press the Cleaning button
fi rst cycle has ended.
• If you want to stop the cleaning cycle, press the Cleaning button
go back to the last cutting length selected. Clip the head back on to use the
appliance again.
• We recommend cleaning the appliance after each use and before putting it away.
• If the LED display screen shows the Cleaning symbol
button, this means that the appliance has not been cleaned following 15
minutes of continuous use. Press the Cleaning button
as described above.
• After cleaning, we recommend pressing the Parking button
button
storage) to store the appliance.
• We strongly recommend adding a few drops of the oil that came with the
appliance to the blades after use, in order to keep the appliance in optimum
condition.
STORAGE
1
Check that the appliance is on and press the Parking button
The Parking symbol
The appliance head unclips and goes back down, taking the combs with it, to go into
the Parking position, which is the ideal position in which to protect the appliance's
blades and combs before storing.
Note
• If the appliance has not been cleaned before you press the Parking button , the
Cleaning symbol
store it.
2
Then put the still-damp appliance away on its stand.

MEMORY FUNCTION

The appliance has a Memory function that saves the last cutting length chosen.
When the appliance is started up, the combs will automatically return to the last selected
cutting height.
button to increase cleaning effi ciency under
twice to start the cleaning cycle again, once the
and clean the appliance
.
is displayed on the LED display screen.
fl ashes, reminding you to clean the appliance before you
17
once to
when you press the
(see chapter on