JVC DT-V1910CG Manual Del Usuario página 5

12 UNDER SCAN button/lamp
Press the UNDER SCAN button. The button
lights and the screen is reduced (under-scan)
and the whole screen is displayed.
• When the UNDER SCAN button is pressed while lit, the
light goes off and the screen returns to normal size
(over-scan).
• Use this function to check the whole screen.
NOTE:
This function is invalid with the RGB-input screen.
PULSE CROSS button/lamp
13
When you press the PULSE CROSS button, the
button lights and the picture moves horizontally
and vertically. The synchronized signal is dis-
played and the screen automatically brightens to
make it easier to confirm the synchronized
sections.
• When the PULSE CROSS button is pressed while lit,
the light goes off and the normal screen is restored.
NOTE:
This function is invalid with the RGB-input screen.
14 COLOR OFF button/lamp
When you press the COLOR OFF button, the
button lights and the screen becomes mono-
chrome. Only the brightness signal is displayed.
• When the COLOR OFF button is pressed while lit, the
light goes off and the normal screen is restored.
• Use this function to confirm the noise in the brightness
signal or to confirm the white balance.
NOTE:
This function is invalid with the RGB-input screen.
15
SCREENS CHECK button/lamp
Press the SCREENS CHECK button. The button
lights and the screen changes in the following
order:
Normal screen[Red screen[Green screen
• Press the SCREENS CHECK button when the blue
screen is displayed. The light goes off and the normal
screen is restored.
• Use this function to confirm or adjust CHROMA or
PHASE.
NOTE:
This function is invalid with the RGB-input screen.
ASPECT button/lamp
16
When the ASPECT button is pressed while the
screen ratio is 4:3, the button lights and the
screen ratio changes to 16:9.
• When the ASPECT button is pressed while lit, the light
goes off and the normal screen is restored.
NOTE:
This function is invalid with the RGB-input screen.
Blue screen
AREA MARKER button/lamp
17
This button turns the AREA MARKER function
ON/OFF.
• AREA MARKER function includes MARKER, ZOOM,
and SAFETY AREA functions. Refer to "AREA
MARKER" on page 16 for more information.
• When AREA MARKER is set to ON, the button lights.
NOTES:
• Functions do not operate when they are set to OFF in the
"AREA MARKER".
• Initial setting of each function in the "AREA MARKER" Menu is
OFF. Before you can use the AREA MARKER function, you
must change the "AREA MARKER" Menu settings first. Refer
to "AREA MARKER" on page 16 for details.
• This button does not operate when RGB is input.
• The ZOOM function does not operate in the under-scan mode.
INPUT SELECT button
18
Selects an input signal from one of the input
cards installed in the monitor's card slots
(SLOT1 – SLOT3).
Select SLOT1: press A or B
Select SLOT2: press C or D
Select SLOT3: press E or F
Refer to the input card instructions on pages 7 and 8 for
details on the correspondence between the input terminals
and the INPUT SELECT buttons.
• The INPUT SELECT button corresponding to the
current input signal lights.
• When the input is switched, the new input status is
displayed on the screen for about 3 seconds.
• To display the current input status again, press the
illuminated INPUT SELECT.
About status display
Displays information on the current input selection and
the monitor settings.
INPUT C ................ Selected input
VIDEO ................... Input card status (*1)
NTSC .................... Signal format (*2)
HIGH ..................... Setting of "COLOR TEMP." (*3)
EXT SYNC ............ External synchronization (*4)
*1 Notes
• "NO SLOT" is displayed when there is no input card inserted in
the slot corresponding to the selected input.
• "COMP." or "RGB" is displayed when a component or RGB
signal (input from COMPONENT/RGB INPUT CARD) is
selected.
• "VIDEO(Y/C)" is displayed when S-video is input from VIDEO
2(INPUT SELECT B/D/F).
*2 Notes
• "NO SYNC" is displayed when no video signal is input.
• When "SYNC SELECT" is set as "EXT" (external), "NO SYNC"
is displayed even when a video signal is input and a synchro-
nized signal is not input. Refer to "SYNC SELECT" on page 19
for more information.
*3 Note
Refer to "COLOR TEMP." on page 20 for details on "COLOR
TEMP" settings.
*4 Note
When "SYNC SELECT" is set to "INT." (internal synchronization),
no message is displayed. Refer to "SYNC SELECT" on page 19
for more information.
5