Coupling With Bluetooth® Devices; Connections With Other Devices - Cellular Line btsplitter35 Manual De Instrucciones

Follow these instructions to recharge:
Step 1: Connect the cable supplied to a normal USB port on the PC or to a
battery charger with USB output;
Step 2: Connect the other end of the cable to the BTSPLITTER35 charging
port . (part number 2)
Red LED on: Charging .
Red LED off: Charging complete .
About 2 and 1/2 hours are needed to fully charge the BTSPLITTER35 .
Note:
Do not try to remove the battery from the transmitter in order to
avoid damaging the transmitter .
attention:
1) The battery can be recycled .
2) Do not throw the battery in fire as it could explode .
2. Turning the BTsPliTTer35 on/off
Function
Turn on the Press the MFB button
BTSPLITTER35 for 3-4 seconds
Turn off the Press the MFB button
BTSPLITTER35 for 3-4 seconds
Activate coupling Press the MFB button
mode for 4-5 seconds
3. Coupling with Bluetooth® devices
Coupling with the first device
After having coupled the BTSPLITTER35 to two Bluetooth® devices, you
can listen to the same music wirelessly . Before coupling, make sure your
Bluetooth® receiver supports the Bluetooth® A2DP profile (InterphoneF4 /
InterphoneF5) .
Follow these instructions for coupling with the first device:
1) Make sure the BTSPLITTER35 is off, or, if not, turn it off;
2) Keep the BTSPLITTER35 and the Bluetooth® stereo receiver at a distance
of no greater than 5 meters from each other .
3) Prepare the first Bluetooth® receiver to be coupled .
Using InterphoneF4/F5, with the Interphone off, press and hold down
the main MFB button for about 10 seconds, releasing it when the LED
flashes from red to blue . For other headphones and Bluetooth® devices,
consult the manual for the exact procedure .
16
4) Press the MFB button on the BTSPLITTER35 for 4-5 seconds, release and
operation led indicator
The blue LED will flash
for 1 second
The red LED will flash
for a second and then it
will shut off .
The red and blue LEDS
will flash intermittently
wait until the red and blue LEDs flash intermittently signalling that the
BTSPLITTER35 has entered "coupling" mode .
5) BTSPLITTER35 will seek the Bluetooth® receiver and connect automati-
cally .
6) After having established the connection, the blue LED on the BTSPLIT-
TER35 will flash once every 4 seconds;
7) Connect BTSPLITTER35 to the music player through the 3 .5 mm audio
mini-jack .
Coupling with the second device
1) After having connected BTSPLITTER35 with the first device, prepare the
second Bluetooth® to be coupled .
Using InterphoneF4/F5, with the Interphone off, press and hold down
the main button for about 10 seconds, releasing it when the LED flashes
from red to blue . For other headphones and Bluetooth® devices, consult
the manual for the exact procedure .
2) Double click on the BTSPLITTER35 MFB button to enter coupling mode
again (the blue LED will flash quickly); now you can couple the second
device . Coupling mode will last for 2 minutes .
3) After having connected BTSPLITTER35 with the two devices, the blue
LED on the transmitter will flash twice every 4 seconds .
Notes:
Coupling mode will last 2 minutes . If the connection is not completed
-
successfully within 2 minutes, the transmitter will return to stand-by
mode (not connected) .
BTSPLITTER35 can keep up to 8 devices in memory . If more than 8 devi-
-
ces are coupled, the first device coupled will be replaced .
- BTSPLITTER35 can only be coupled with Bluetooth® stereo receivers that
use one of the following PIN numbers: 0000, 1234, 1111, 8888 .

4. Connections with other devices

1) automatic connection
Each time the BTSPLITTER35 is turned on, it will attempt to connect auto-
matically with the last connected device .
2) manual connection
When BTSPLITTER35 is in stand-by mode, briefly press the MFB button to
attempt automatic connection with the last connected device .
3) Connected
BTSPLITTER35 can be connected to a previously coupled receiver when it is
in stand-by mode but cannot be connected to new devices .
IT
EN
FR
ES
DE