Publicidad
EN
IMPORTANT
Please read these instructions carefully before you start to assemble this greenhouse.
Keep these instructions in a safe place for future reference.
When encountering the information icon, please refer to the
relevant assembly step for additional comments and assistance.
This icon indicates that the installer should be inside the product.
»
Customer Service
For assistance with assembly or for replacement parts – please log onto our website
or call our service line (number is on the title page).
Additional information can be found at our website: www.palramapplications.com
»
Safety Advice
•
It is of utmost importance to assemble all of the parts according to the directions.
Do not skip any step.
•
We strongly recommend using work gloves during assembly.
•
Always wear shoes and safety goggles when working with extruded aluminium.
•
If using a step ladder or power tools ensure that you follow the manufacturer's safety
advice.
•
Do not touch overhead power cables with the aluminium profiles.
•
Do not attempt to assemble the greenhouse in windy or wet conditions.
•
Dispose of all plastic bags safely keep them out of reach of small children.
•
Keep children away from the assembly area.
•
Do not lean against or push the greenhouse during construction.
•
Do not position your greenhouse in an area exposed to excessive wind.
•
Do not attempt to assemble this greenhouse if you are tired, have taken drugs
or alcohol or if you are prone to dizzy spell.
•
Hot items such as recently used grills, blowtorches etc. must not be stored in the
greenhouse. Ensure there are no hidden pipes or cables in the ground before
inserting the pegs.
•
This product is designed to use as greenhouse only.
»
Care & Maintenance
When your greenhouse needs to be cleaned, use a mild detergent solution and
rinse with cold clean water. DO NOT use acetone, abrasive cleaners or other special
detergents to clean the clear panels. It is recommended to check periodically that
roof panels caps (plastic part 329 & profile 981) are set in place.
»
Tools & Equipment
T001 - Special tool for Screws 411 and nuts 412
Before Assembly
This is a multi-part assembly best
achieved by two people. Allow at least
half a day for assembly process.
Selecting a site - the greenhouse must
be, positioned and fixed on a flat level
surface.
Choose a sunny position away from
overhanging trees.
We are strongly recomend to fix
your greenhouse directly to a solid
concrete foundation. When doing that
use the pre drilled holes in the metal
base supplied.
Take out all components parts of the
packages. Sort the parts and check
against the contents parts list.
During assembly parts should be laid
out close at hand. Keep all small parts
(screws etc.) in a bowl so they do not
get lost.
•
Screws 411 and nuts 412 are used throughout the assembly process.
•
Screws 411 are to be assembled from the outside and nuts 412 from the inside of the
greenhouse.
•
If not specified otherwise, do not fasten screws and nuts (411 & 412) more than
2-3 turns only. Do not tighten them until completion of the panels' assembly.
These 2 icons indicate if screws' tightening is required or not.
•
However, in some steps, temporary tightening of a few screws may be needed to
prevent a profile from falling till it will be fully connected in the next steps.
During Assembly
Carry out the assembly steps in the order
set out in the instructions.
You may use Silicon lubricant spray in
order to help you slide the profiles on the
connectors.
Do not spray the Polycarbonate
panels.
Use the rubber malet if necessary.
Step 3: Part 7063 is the greenhouse
threshold.
Fixing it determines the front side of the
greenhouse.
Step 10: Make sure the base is square
by measuring the diagonals and level
by using a spirit level.
Firmly connect the greenhouse to a
level final position immediately after
completion of the assembly.
Steps 15: Part 7180 is used for assembly
assistance.
Steps 29: Remove Part 7180 and discard.
Steps 50+51: Please repeat steps
47-49 and work according to the parts id
mentioned in this manual.
Step 70 : In case the window is not closed
properly, please release the screws, adjust
the profile and tighten the screw.
Tighten all screws when completing
assembly.
Publicidad
