Publicidad
Idiomas disponibles
Idiomas disponibles
01900
FM radio tuner with RDS, coaxial connector for external FM aerial, inte-
grated line terminator, installation on DIN rail (60715 TH35), occupies 2
modules of 17.5 mm.
The FM tuner is able to send the digital audio signal and the RDS messages received by radio
over the bus. The FM tuner receives the radio stations (with the relevant RDS information) in the
band 87.50 – 108.00 MHz and in addition enables saving up to 8 different radio stations, to then
be able retrieve them by using the commands sent over the bus by the By-me control devices.
CHARACTERISTICS.
• Rated supply voltage BUS 29 V
• Terminals:
1) 2 for the speaker system bus
2) 2 for a bus By-me output for connecting up to 3 By-me devices
• Absorption: 35 mA
• Dissipated power: 1 W
• Installation: on DIN rail (60715 TH35), size 2 modules
• Operating temperature: -5 - +45 °C (for indoor use)
• Configuration button
• Possibility of manual adjustment of input sensitivity (see control unit manual)
• Two-colour LED for configuring and indicating ON/OFF status of operation
• F-type female connector for external antenna
• Jumper to insert the audio line termination
• Jumper to select the type of antenna (external on connector F or use the Bus cable as an antenna)
CONFIGURATION.
FOR CONFIGURATION OPERATIONS, SEE THE By-me SYSTEM INSTRUCTIONS
MANUAL ATTACHED TO THE CONTROL UNIT.
• Functional blocks: 1
• To select the functional block (configuration): during group creation, press the configuration
button and wait for the red LED to light up.
With the red LED on, the control unit will configure the functional block; at the end of this
operation the red LED will go out.
Settings which can be configured directly from the device
• To set the type of antenna, that is to say external on connector F or internal on the bus, it is
sufficient to use the PIN STRIP situated next to the antenna connector (fig. 2):
1. Antenna on connector F: Connect together pins 3 with 5 and 4 with 6
2. Antenna on bus: Connect together pins 3 with 1 and 4 with 2
IMPORTANT: If there is no additional branch from the audio bus terminal to connect
other audio devices (if the device is the first and last of an audio branch), the bridge
near the terminal (fig. 3 - line termination) must be closed; otherwise it must be left open.
Each end of the speaker system bus must always be terminated.
INSTALLATION RULES
Installation should be carried out in compliance with the current regulations regarding the instal-
lation of electrical systems in the country where the products are installed.
WARNING: If the external antenna is used on connector F the device must be suitably sepa-
rated from the circuit with hazardous voltage. The antenna is a SELV circuit.
CONFORMITY.
EMC directive.
Standards EN 50428, EN 55022, EN 55024.
3
Bridge to terminate the
audio line open
Viale Vicenza, 14 - I 36063 Marostica VI
Tel. +39 0424 488 600 - Fax (Export) +39 0424 488 709
www.vimar.com
Closing the bridges
with the jumpers
FRONT VIEW AND CONNECTIONS
01900
FM TUNER
CONF.
By-me
BUS
+
-
+
Automation system
Speaker system bus
TP bus terminals
terminals
(max 3 devices)
1
Connector F for
external antenna
2
1
2
3
4
5
6
Antenna on bus cable: bridge posi-
tioned on PIN 3-1 and PIN 4-2
Antenna on connector F: bridge
positioned on PIN 3-5 and PIN 4-6
ENGLISH
Instruction sheet
LED and configuration
button
-
PIN-STRIP to select
the type of antenna by
means of the bridge
supplied
1
2
3
4
5
6
1
2
3
4
5
6
Publicidad
