General Remarks - Akasa integral NMAX Manual Del Usuario

HARD DISK FORMATTING
WARNING!
Before you partition or format your hard disk, please be aware that this will destroy all your
existing data on the drive, so make sure you have a backup if required. This step is usually only
required the first time you install a factory new hard drive or if you want to change the existing
format of the drive.
Windows 2000/XP/VISTA
Step1
To partition the drive please connect the enclosure either via USB or eSATA
connection then go to "START", right-click on [My Computer] and choose
[Manage]. A [Computer Management] window will appear.
Step2
Click on [Disk Management] on the left part of this window and all connected
disk drives will be listed in the right part. Find the Hard Disk that you added with
it's partition status on the right. You can create a new or delete an existing
partition by right clicking on this area.
Step3
Right-click on the hard disk partition status area and choose
[New Partition...].The "New partition wizard" will appear.
Step4
Following the "wizard" instructions to partition and format your HDD.
Step5
Wait until the "wizard" finished formatting your eSATA drive. It should now appear in
[My Computer] ready to use.
Mac OS
Mac OS does not recognize NTFS formatted drives.
Mac OS9.2 and earlier, does not support creating partitions on an external drive. To do that,
you would need to purchase additional rd party software.
Initializing is no problem on all Operating Systems. Mac OS X, use the Disk Utility to format
and create partitions on your external disk.
• Select "Disk Utilities" in the utilities folder.
• Choose your external drive and format it according to your requirement.

GENERAL REMARKS

• Only one interface (USB or eSATA) can be connected at the same time.
• For better heat dissipation and performance, do not cover the Enclosure and leave enough
room around it.
• Never expose the product to water or humid conditions.
0
HDD formatting
FAQ
1. Does the enclosure need any drivers?
The embedded drivers of Windows 2000/XP/VISTA control the enclosure and there are no
additional drivers required.
2.When do I need to format the HDD?
Only if it is brand new or you want it to use with different file format.
3. Is there a HDD imitation?
All capacity of SATA I and SATA II hard drives up to 2.5mm high are supported.
4. Do I need to restart the system when connecting the enclosure via eSATA?
Most motherboards don't support the Hot Swap on eSATA/SATA connection but some do.
Please refer to your motherboard manual.
5. My system doesn't have an eSATA port, can I still use the enclosure?
You can use the enclosure in USB mode or equip you PC system with a SATA to eSATA
adapter / SATA to eSATA cable and your Notebook with an eSATA expansion
card.
6. Do I need to use USB-to-DC cable in USB mode?
Most likely yes, but it depends on your HDD power requirements and amount of current
available from your PC / MAC USB.
7. Do I need to use USB-to-DC cable in eSATA mode?
Yes, it is required to power up the enclosure as the eSATA cable only carries data. Some HDD
may only require single USB port to be used but using both is recommended.
8. Can I power the enclosure from the adapter instead of USB ports?
Yes, the compatible product (5V, 2A) from our range is AK-PAHUB.
9. Will my HDD overheat if left on for a long period of time?
No, to prevent the hard drives from overheating the body of the enclosure is made of
thick aluminium, which enhances heat dissipation. Avoid keeping the enclosure near a radiator
or on direct sunlight.
10. I've connected the enclosure but it doesn't appear in the explorer.
If you use eSATA connection, try restarting the system.
If you use USB connection, make sure that both USB connectors are connected to the motherboard.
If you connect the enclosure via a USB hub make sure it has additional power from an adapter.
If you have any more questions please contact as at: technical@akasa.com.tw