Sencor 179-NAB1 Serie Manual De Usuario página 10

Variable Temperature Kettle
SWK 179XXX-NAB1 / SWK 1791WH-NAB1 / SWK 1792BK-NAB1
temperature mode. The water temperature will be maintained for 30 minutes. The variable
temperature kettle will then turn off (switches to stand-by mode). The lights of buttons B2–3
and the water level mark A8 will switch off. The current water temperature will be shown on the
display B1.
Note:
The temperature settings can be changed at any time using button B3. The heat water to
a preset temperature mode or maintain the preset temperature mode can be canceled by
pressing button B2.
If you set a temperature using button B3 and then do not press button B2, the kettle will
revert to the stand-by mode after 5 seconds.
If you press button B2 without fi rst setting the temperature, the water will fi rst heat up to
122°F (50°C) and only thereafter will the kettle switch to the maintain water temperature mode.
4.3 Boil water, cool water to a preset temperature and maintain the preset temperature
Use the button B3 to set a temperature of 122, 140, 158 or 185°F (50, 60, 70 or 85°C), to which the
water should cool after being boiled. Then press the buttons B2 and B4. When buttons B2–4
and the water level mark A8 are lit, it is heating water. Display B1 will switch to the current water
temperature display mode. The set temperature is indicated by the "•" symbol lit up on the display
B1. The variable temperature kettle will start the boil water mode. A sound will be made (5 beeps)
when the water boils. The light of button B4 will switch off. As soon as the boiled water cools
down to the preset temperature, a beep will be made and the variable temperature kettle will
switch to the maintaining temperature mode. The water temperature will be maintained for 30
minutes. The variable temperature kettle will then turn off (switches to stand-by mode). The lights
of buttons B2–3 and the water level mark A8 will switch off. The current water temperature will
be shown on the display B1.
Note:
The boil water mode can be canceled by pressing button B4 again. The temperature settings
can be changed at any time using button B3. The heat water to a preset temperature mode or
maintain the preset temperature mode can be canceled by pressing button B2.
Note:
A sound (beep) is made each time a button is pressed.
Attention:
This variable temperature kettle is not calibrated for scientifi c or laboratory purposes. The actual water
temperature inside the kettle may vary from the temperature shown on the display by 9°F (5°C).
Do not turn on the variable temperature kettle if it is empty. Incorrect use of the variable
temperature kettle may negatively affect its service life. If you accidentally turn on the variable
temperature kettle without water, a sound will be made after a short time. The display B1,
the water level mark light A8 and the lights of the control buttons will switch off. Remove the
kettle from the base and prior to fi lling it up and starting it again, wait several minutes until the
stainless steel bottom cools down.
5. Before taking the kettle off the base A3 make sure that it is turned off (it is in stand-by mode), or
turn it off manually if it is still running. Turn off the kettle by canceling the set mode according to
the instructions contained in paragraph 4.1-4.3.
Pour the boiled or heated water into a prepared container, cup or mug. If you carry the kettle,
make sure that it remains in a horizontal position, particularly if it is fi lled all the way up to the
maximum mark.
If you wish to open the lid A5 to refi ll the kettle, fi rst empty all the contents of the kettle so that
you are not scalded by the escaping steam.
6. After you fi nish using the kettle, disconnect the power cord from the el. power socket. Empty the
kettle and allow it to cool down.
2014
EN-10
10/2014