Magnat SBW 200 Notas Importantes Sobre La Instalación / Certificado De Garantía página 13

Connecting additional devices to the soundbar
Connecting the device to a Bluetooth audio source:
Use the remote control to switch the soundbar to the Bluetooth mode. If you have previously connected a Bluetooth device, the soundbar
will automatically attempt to re-establish a connection with this device. If this is the case, you may be required to manually reconfirm the
connection on the source device. The connection can be resumed from a previously paired source device at any time, as the Bluetooth
function continues to operate in the background regardless of the input selected on the soundbar, and it is only switched off completely
when the standby mode is selected.
If a connection has not already been made or the connection cannot be re-established, the soundbar will automatically activate the
‚pairing mode'. TTo manually activate the soundbar's pairing mode, press the BT button (fig. 2, pos. 10) that is located on the right-hand
control panel of the soundbar. The blue LED will flash as long as the pairing mode is active.
Now activate the Bluetooth mode on your source device. The soundbar will appear in the list of Bluetooth devices as „Magnat SBW200".
If it is not displayed in the list, set your source device to search for Bluetooth devices manually and make sure that the soundbar has
been switched to the pairing mode.
Connecting an analogue or digital audio source to the soundbar:
Additional audio sources such as CD players, MP3 players and satellite receivers can also be connected to the analog input AUX (fig. 2,
pos. 4) and to the digital input OPTICAL (Fig. 2, pos. 5) on the soundbar. When doing this proceed as described in the previous sections.
Connecting a mobile device (mobile phone, MP3 player, etc.) to the USB charging socket USB CHARGE (fig. 2, pos. 3):
Devices that have a USB charging function can be connected to this socket and charged (Charging voltage: 5V, max. charging current: 0.5A).
Please also refer to the instruction manual supplied with the corresponding device!
Connecting the power supply of the soundbar:
Included in delivery is an external mains adapter (C) (110 - 240 V / AC 50/60 Hz).
1. Connect the output cable (jack connector) of the external mains adapter to the power supply jack of the soundbar (fig. 2, pos. 2).
2. Insert the mains adapter into the socket.
Connecting the power supply to the subwoofer:
Included in delivery is the most commonly used mains cable. The mains cable used in your country, however, may be different. If the mains
cable is not compatible with your power sockets or if you are in any doubt, please contact your Magnat dealer.
1. Plug the 2-pole mains cable into the mains socket on the subwoofer amplifier (fig. 3, pos. 16).
2. Insert the mains cable into the socket. Make sure that you are using the mains plug that is compatible with the socket.
INITIAL START-UP, WIRELESS PAIRING OF THE SOUNDBAR WITH THE SUBWOOFER
Switch on the soundbar by using the power switch (fig. 2, pos. 1) and switch on the subwoofer by using the mains switch (fig. 3, pos. 15).
Now activate the soundbar by using the remote control (fig. 4, pos. 17) or the side control panel (fig. 2, pos. 5).
The soundbar and subwoofer will now be paired automatically. The blue LED on the subwoofer will flash during this process. When pairing is
successful, the LED will illuminate permanently. This can take up to 30 seconds.
If the automatic pairing process fails (the LED flashes continuously), please press the PAIR button on the subwoofer (fig. 3, pos. 14) to repeat
the pairing process.
When the subwoofer has been successfully paired, it will connect within a few seconds every time the soundbar is switched on.
Please note: If the soundbar is switched to the standby mode, the subwoofer will also enter the standby mode automatically after a few
seconds. The blue LED on the subwoofer will flash initially and then go out.
13