Before Welding - Tool it Professional SPACEVIEW 5-9 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 11
The welding helmet SPACEVIEW 5-9/9-13 complies with EEC directives 89/686 CEE. This confirmity is established in compliance with EN 175, EN 166, EN 168 and EN 379.
This welding helmet is delivered ready for use. For your protection, please read carrefully these instructions and consult with a qualified instructor prior to operation.

BEFORE WELDING

-Check that the welding helmet is in good condition and headband adjustment.
-Check whether the front cover lens, the front frame and filter are inserted and fixed in place. In case of anomalie, please proceed to its reconditionning.
-Make sure that the 4 sensors (7) and the 2 cells (6) are not obstructed by dust or debris.
-Make sure that the protection films on both screens are removed.
-Make sure that the red light (4) is off, otherwise change the batteries (10).
-Check that the protection level matches your welding processes. Please refer to the following chart to help your choice (cf. welding process board)
OPERATION
The SPACEVIEW 5-9/9-13 auto-darkening welding helmet switches from light to dark state when a welding arc is struck. The auto-darkening welding helmet switches back to
the light state when the arc stops.
1
2
3
4
9
5
10
• Internal sensitivity potentiometer : Sensitivity adjustable according to :
- Light ambient: Without welding, turn the sensitivity setting towards «max», then turn the sensitivity setting towards «low» until filter lightens.
- Welding process: «Max» position for low amperage TIG rpocess / Medium range for most application.
• Internal delay potentionmeter: Controls the delay for the helmet to switch back to clear after welding.
Delay is designed for slower switching time to clear state to eliminate remained bright rays.
The internal shade range selector allows to choose the shade range between 5-9 or 9-13.
The external potentiometer allows to adjust the shade according to the selected shade range.
• "GRIND" knob : For non-welding operation, you can switch off the filter on « Grind » mode. The Grind led will blink to confirm the filter is off.
WARNING: To be protected before welding, carefully check the switch to be on WELD mode
PRECAUTIONS
• The welding helmet is suitable for use with virtually all welding processes except Oxy-Acetylene welding, laser welding and gas welding.
• Standard protective screens must be installed on both inside and outside surfaces of the module. Failure to use protective screens may constitute a safety hazard or result in
irreparable damage to the module.
HEADBAND ADJUSTMENT
The SPACEVIEW 5-9/9-13 is equipped with a headband which can be adjsuted in multiple ways to suit the welder: width, height (1), longitudinal inclination (3) and adjust-
ment (2).
V5-17/02/16
EN
1. Sensitivity control knob
2. Delay time control knob
6
3. Shade adjustment 5-9/9-13
4. Low battery alarm
5. LCD protection plate
9
6. Solar cell
7
7. Sensors
8
8. Filter
6
9. Potentionmeter «Welding-Grinding»
10. Pile lithium 3V (x2) CR2032
Clear shade
4
Dark shade
5-9 / 9-13
Filter dimension
114 x 133 x 9 mm
Reaction speed
0,0001 s
Power supply
Solar + batteries
Weight
530 gr
Field of vision
100 x 93 mm
Applications
MMA 5>400 / TIG 2>300 / MIG-MAG 5>400 / Grind
Warranty
1 year
Application temperature
-5°C / + 55°C
Storage temperature
-20°C / + 70°C
3
1
2
5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Professional spaceview 9-13Professional spaceview 5-9

Tabla de contenido