Lutron RadioRA2 RRD-W1RLD Instrucciones De Instalación

044352 Rev. A
08/2019
Installation Instructions
Please Read Before Installing
RRD-W1RLD RRD-W3BRL RRD-W4S
RRD-W2RLD
RRD-W3BSRL RRD-W5BRL
RRD-W3BD RRD-W3S RRD-W5BRLIR
Use these instructions to install the model numbers listed above.
For system setup guide and tools visit:www.lutron.com/radiora2
Important Notes
Codes: Install in accordance with all local and national electrical codes.
Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), 0 to 90%
humidity, non-condensing. Indoor use only.
Wallplates: Use only Lutron wallplates with these devices. The mechanical design of the
keypad is NOT compatible with non-Lutron wallplates. Non-Lutron wallplates will NOT sit flush
against the wall. Claro and Satin Colors wallplates are strongly recommended for best color
match and clean aesthetic appearance. Do not paint controls, buttons, or wallplates.
Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical cleaning
solutions.
Wallboxes: All keypads require a U.S. wallbox. 3 ` in (89 mm) deep recommended, 2 1 in
(57 mm) deep minimum.
RF Device Placement: RF dimmers, switches, keypads and shades / drapes must be located
within 30 ft (9 m) of an RF signal repeater. For systems without an RF signal repeater, all RF
dimmers, switches, keypads and shades / drapes must be located within 30 ft (9 m) of each
other. Remote dimmers and switches are not required to be within a specific range.
Engraving: The Prepaid Engraving Certificate included with the keypad can be redeemed for
a custom engraved replacement kit. To order an engraved replacement kit please follow the
instructions at: www.lutron.com/buttons
Raise / Lower Default: Raise / lower the last button pressed.
* Typical Power Consumption test conditions: all backlights on medium intensity, two LEDs on (two presets
active), keypad powered at 120 V~
Customer Assistance
www.lutron.com/support
For questions concerning the installation or operation of this product, call
Lutron Customer Assistance. Please provide exact model number when calling.
U.S.A. and Canada (24 hrs / 7days) Brazil (M-F 8:30 – 17:30 BRT)
1.844.LUTRON1 +55 (11) 3257.6745
Mexico (8am – 8pm ET) Other countries (8am – 8pm ET)
+1.888.235.2910 +1.610.282.3800
Lutron Elec tron ics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Installation
English
WARNING
Wall-mount Designer Keypads circuit breaker in the OFF position before proceeding. Wiring with power ON could result in
serious injury or death.
120 V~ 50 / 60 Hz 0.5 A
Typical Power Consumption*: 0.6 W
1. Turn power OFF at fusebox or circuit breaker.
RRD-W6BRL
RRD-W7B
2. Prepare wires. When making wire connections, follow the recommended strip lengths and
RRD-W
combinations for the supplied wire connectors. Note: Wire connectors provided are suitable for
copper wire only.
• Strip insulation 3/8 in (10 mm) for 14 AWG (1.5 mm
• Strip insulation 1/2 in (13 mm) for 18 AWG (0.75 mm
• Use to join one 14 AWG (1.5 mm
3. Wire control.
Hot/Live
120 V
50 / 60 Hz
Neutral
4. Push all wires back into the wallbox and loosely fasten the control to the wallbox using the
keypad mounting screws provided. Do not pinch the wires. See Mounting Diagram below.
Mounting Diagram
Wallbox
5. Install Replacement Kit (if applicable).
6. Attach Lutron Claro or Satin Colors wallplate adapter and wallplate
(see Mounting Diagram).
a. Install the wallplate adapter onto the front of the keypad(s).
b. Tighten keypad mounting screws until wallplate adapter is flush to wall
(do not over-tighten).
c. Snap wallplate onto wallplate adapter and verify that buttons are aligned properly.
d. If control(s) are misaligned, loosen keypad mounting screws appropriately.
7. Restore power.
)Lutron, Lutron, RadioRA, Claro, Pico, RadioRA 2, FASS, and Satin Colors are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries.
©2013 – 2019 Lutron Electronics Co., Inc.
Shock Hazard. To avoid the risk of electric shock, locate and remove fuse or lock
:
).
2
2 ).
) with one 18 AWG (0.75 mm ) wires.
2 2
NOTE: Orientation arrow
Black
MUST point UP.
White Green / Bare
Adapter
Wallplate
Mounting
Keypad Wallplate
Screws
Mounting Adapter
Screws
Replacement
Kit
Keypad
System Setup
This keypad can be used in a RadioRA 2 system with a Main Repeater for control of
dimmers, switches, and shades. Use the RadioRA 2 programming software to setup the
system (training required to access the software).
Troubleshooting Guide
Symptom Probable cause and action
LEDs on a keypad Power not present at keypad
don't light up when • Circuit breaker OFF. Turn ON breaker.
buttons on it are
Incorrect wiring.
pressed.
• Wire the keypad according to the Installation section.
A specific The dimmer, switch or shade / drapery is not assigned
dimmer, switch or to keypad.
• Refer to the RadioRA2 programming software and ensure the
shade / drapery not
controlled when a device is assigned to the keypad.
button is pressed on Perform a transfer and make sure it is successful.
a keypad.
The device is 'unaffected' for that button.
• Refer to the RadioRA2 programming software and ensure the
device is checked to be 'unaffected'.
Perform a transfer and make sure it is successful.
The lamp(s) controlled by the dimmer/switch is (are)
burned out.
• Replace the lamp(s).
Either there is no power to the device or the FASS switch is pulled
out on a dimmer / switch.
• Ensure that the device is powered and push the FASS
switch in.
Ground
Devices are out of range.
• Check to make sure all Pico wireless controls, keypads,
dimmers, switches and shades/draperies are within
30 ft (9 m) of each other.
Dimmer, switch or The button was not programmed correctly.
• Refer to the RadioRA2 programming software and ensure the
shade / drapery does
not go to the desired device is assigned to the keypad.
level or position Perform a transfer and make sure it is successful.
when a button on the
The device is 'unaffected' for that button.
keypad is pressed.
• Refer to the RadioRA2 programming software and ensure the
device is checked to be 'unaffected'.
Perform a transfer and make sure it is successful.
The button pressed is the bottom button.
• The bottom button cannot be saved or modified.
Devices are out of range.
• Check to make sure all Pico wireless controls, keypads,
dimmers, switches and shades/draperies are within
30 ft (9 m) of each other.
All LEDs on the The keypad is in the Factory Settings mode and has not been
keypad flash when configured to work in a system.
any button is • Refer to the RadioRA2 programming software and ensure the
pressed. device is assigned to that keypad.
Perform a transfer and make sure it is successful.
Note: Refer to the system Setup Guide for additional troubleshooting suggestions.
Returning Keypads to Factory Settings
Note: Returning a keypad to its Factory Settings will remove it from the system and erase
all programming.
Step 1: Triple tap and hold either the top or bottom button on the keypad. DO NOT
release the button after the third tap.
Step 2: Keep the button pressed on the third tap until the LED next to the top button turns
on solid (approximately 3 seconds).
Step 3: Immediately release the button and triple tap it again. The LED next to the top
button will flash quickly. When the LED stops flashing, the control has been
returned to Factory Settings.
Warranty: For warranty information, please see the warranty enclosed with the product, or
visit www.lutron.com/TechnicalDocumentLibrary/Warranty.pdf