Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
HDMI® HDB
T + VGA, 3.5
ASE
T
B
R
RANSMITTER TO
OX
F
EATURES
One-way Power over HDBaseT (PoH), so that the wall plate can be powered by receiver.
•
Extend 4Kx2K at 60Hz (4:2:0) up to 130ft and 1080p at 60Hz up to 230ft with Cat 6a/7 cable
•
Extend 4Kx2K at 60Hz (4:2:0) up to 115ft and 1080p at 60Hz up to 200ft with Cat 5e/6 cable
•
HDMI 1.4 with 4K at 60Hz, 4:2:0, 8bit and HDCP 2.2 compliant
•
One-way analog audio pass through from wall-plate transmitter to receiver.
•
Supports automatic switching.
•
Two buttons on the panel, one for input switching and the other to turn display on/off (CEC).
•
Supports USB 2.0 pass through over HDBT, connecting up to 4 USB devices to the receiver.
•
Supports firmware updates through the USB Micro-B port on the Transmitter.
•
M
B
I
OUNTING
RACKET
NSTALLATION
Note: Before installation, please ensure the unit is disconnected from the power source.
1.
Choose a suitable location for mounting bracket installation.
2.
Position and install the mounting brackets of the receiver with the two mounting screws
provided.
3.
Mount and secure the receiver to a surface or a suitable location respectively with
mounting screws.
C
I
ABLE
NSTALLATION
Note: Before installing cables, please ensure the unit is disconnected from the power source.
1.
Connect HDMI IN: Connect an HDMI source device (e.g. Laptop, Blu-ray player, etc.) to HDMI IN of the transmitter using a high-quality HDMI
cable.
2.
Connect VGA IN: Connect a VGA source device (e.g. Laptop, desktop, etc.) to VGA IN of the transmitter using a VGA cable.
3.
Connect USB-B HOST PORT: Using the included USB-A to B Cable, connect the USB-A end to source device (e.g. Laptop, etc.) and connect the
USB-B end to the USB HOST PORT on the wall plate transmitter.
4.
Connect HDBT: Connect HDBT Out of the transmitter to the HDBT IN of the receiver using a Cat 5e/6/6a cable.
5.
Connect HDMI OUT: Connect an HDMI display device (e.g. TV, monitor, projector, LCD/LED display, etc.) to HDMI OUT of the receiver.
6.
Connect AUDIO OUT: Connect an amplifier to the AUDIO OUT of the receiver using a 3.5mm audio cable.
7.
Connect USB DEVICES: Connect up to four USB devices (e.g. keyboard, mouse, USB camera, etc.) to the USB DEVICE ports of the receiver.
8.
Power on all attached devices.
,
USB-A
MM
AND
- 4K 60H
ECEIVER
Z
B
C
E
TO
OVER
AT
XTENDER
4
W
P
ALL
LATE
P
C
ACKAGE
ONTENTS
1 x Wall Plate Transmitter with screws
•
1 x Wall Plate Plastic Panel (2-gang US,
•
with Screws)
1 x 3.5mm 2-Pin Phoenix connector
•
1 x USB-A to B Cable
•
1 x Receiver
•
1 x 12V Power Adapter
•
2 x Mounting Bracket (with screws)
•
1 x 3.5mm 3-Pin Phoenix Connector
•
1 x Manual
•
(
)
US
(
)
US
Publicidad
Tabla de contenido
