AVS Electronics OUTSPIDER PA Manual Del Usuario página 18

Hole for joint adjustment
In case you need to adjust the position of
the sensor, the board is designed with a
hole to easily access the joint screw,
without having to remove the board from
its housing.
The hole is placed over the top PIR so in
order to use it, it is necessary to lift the
adhesive foam located over the hole.
HOLE FOR JOINT
ADJUSTMENT
Recommendations
OUTSPIDER PA
OUTSPIDER PA is equipped with a buzzer
and a series of LED in order to give an
optical-acoustic signal (Walk Test) even if
a block is applied to the sensor.
1.0
1.5
2.2
2.7
MW
YELLOW RED
GIALLO ROSSO
USB
LED
BUZZER
L E D
Y l e o l w S e t a d : y P a s i s e v f n i a r e r d
s g i n l a
F a t s a l f s h n i : g A i t n m a k s l a r a m s
S o l w a l f s h n i : g D r i y t e l s n e s a f l u s t
F a l s h n i : g l A e t n r a e t y l i w h t
L E D f o r a b o t u
s e c o n d s t a r i f t s e f
R e d S e t a d : y G e n r e l a l a r a m s g i
F a l s h n i : g A e t l n r a e t y l i w h t e y
L E D f o r a b o t u
s e c o n d s t a r i f t s e f
When powering the first time, OUTSPIDER
PA remain inhibited for about 60 seconds,
during which the yellow and red LED, if
enabled, flash alternatively and the buzzer
emits an intermittent signal.
Recommendations
OUTSPIDER PA WS 4
OUTSPIDER PA WS 4 is equipped with a
buzzer and a led to provide a visual-
acoustic warning (Walk Test)
MW
GREEN
ROSSO
BUZZER GREEN LED
L E D
G e r e n S e t a d : y G e n r e l a l a
l a r a m
F a l s h n i : g A e t l n r a e t
L E D o f r
g i n l a
s e c o n d s t a
g i n l a
e r d
6 0
e d n i g
At the first power supply of the
n l a
OUTSPIDER PA WS 4 it is necessary to
o l l w
let the sensor rest with the cover on for
6 0
about 90 seconds during which time it
e d n i g
acquires the average signal of the various
analog signals it will be controlling. It is
important that the cover is kept closed so
that it does not distort the average anti-
mask signal and to avoid false detections.
- 18 -
Recommendations
OUTSPIDER DT WS (UB) (U)
OUTSPIDER PA WS (UB) (U) are
equipped with a buzzer and a led to
provide a visual-acoustic warning (Walk
Test)
1.5
2.2
2.7
MW
BATT
RED
ROSSO
USB
BUZZER RED LED
L E
r a m s g i n l a R e d S e t a d : y G
y l i w h t e y o l l w F a l s h n i : g A
a b o t u 6 0 L
r i f t s e f e d n i g s
At the first power supply of the
OUTSPIDER PA WS (UB) (U) it is
necessary to let the sensor rest with the
cover on for about 90 seconds during
which time it acquires the average signal
of the various analog signals it will be
controlling. It is important that the cover
is kept closed so that it does not distort
the average anti-mask signal and to avoid
false detections.
1.5
2.2
2.7
BATT
USB
E
N
G
D
e n r e l a l a r a m s g i n l a
e t l n r a e t y l i w h t e y o l l w
E D o f r a b o t u 6 0
e c o n d s t a r i f t s e f e d n i g