Adjustment Instructions - McCulloch MTR1200 Manual Del Usuario

be hurled 50 feet or more, causing injury or damage to nearby property such as automobiles, homes
and windows. Inspect area before starting the appliance to remove debris and other objects that can
cause damage during operation.
14. DO NOT USE ACCESSORIES or attachments except as recommended and provided by McCulloch.
Do not use any type of wire or metal cutting line.
15. DO NOT OVERREACH - Keep firm footing and balance at all times.
16. AVOID UNINTENTIONAL STARTING - Do not carry plugged in trimmer with your finger on the
switch.
17. DISCONNECT trimmer from power supply when not in use and before servicing REX stringhead.
18. STORE idle trimmer indoors. Appliance should be stored in a dry, high or locked up place - out of the
reach of children.
1-2. EXPLANATION OF NOTE, WARNING, and WARRANTY SYMBOL
1. A NOTE is used to convey additional information, or highlight a particular explanation, or to expand
a step instruction.
2. A WARNING identifies a procedure which, if not undertaken or if improperly done, can result in a seri-
ous personal injury or damage to the unit and/or both.
3. (WARRANTY SYMBOL) serves notice that unless instructions or procedures are followed, any
damage will void the warranty and repairs will be at owner's expense. Service other than user
maintenance should be performed by a McCulloch Authorized Service Center. Damage or conditions
caused to improper maintenance practices which render this product inoperable will void the manu-
facturer's warranty.
4. FOR WARRANTY OR SERVICE contact the nearest McCulloch Authorized Service Center listed
under "SAWS" in your telephone directory Yellow Pages.
1-3. INTERNATIONAL SYMBOLS
1. Read the User Manual (Figure 1-1).
2. Use of these personal safety items is highly recommended to reduce the risk of accidental injury (Figure 1-2).
SAVE THESE INSTRUCTIONS
2 - ASSEMBLY INSTRUCTIONS
NOTE: The only assembly required for your trimmer is to install the debris shield and adjust the assist handle.
2-1. DEBRIS SHIELD INSTALLATION
1. Position the motor housing with string head carrier facing up (Figure 2-1).
2. Slide debris shield over motor housing as shown (Figure 2-1).
3. Align edging guide with mating grooves and push firmly in the direction shown until an audible snap is heard
(Figure 2-2).
NOTE: Be certain that edging guide is oriented as shown. Once edging guide, motor housing and debris shield are
mated the connection is permanent and cannot be removed without a special tool.
2-2. REX DISPOSABLE CUTTING HEAD INSTALLATION AND REMOVAL
INSTALLATION
1. Unplug unit.
2. Position the motor housing with the string head carrier facing up (Figure 2-3).
3. Align disposable string head locking tabs with corresponding slots in carrier as shown (Figure 2-4).
4. With firm pressure push disposable string head onto carrier until an audible click is heard.
REMOVAL
1. Unplug unit.
2. Press red button on top of motor housing to eject used REX disposable string head (Figure 2-5).

3 - ADJUSTMENT INSTRUCTIONS

3-1. ADJUSTABLE ASSIST HANDLE
1. Grip underside of assist handle. With thumb and forefinger on either side of the base of the assist handle as
shown (Figure 3-1).
2. While depressing red buttons, use other hand to move assist handle into desired location.
NOTE: The assist handle is ratcheted for variable operating positions. Adjust to a comfortable position.
3. Release red buttons.
3-2. ADJUST SHAFT LENGTH
1. Grip shaft firmly.
2. Push red shaft release button forward and move handle forward or backward to desired length (Figure 3-2).
NOTE: Shaft may be adjusted in trimming or edging mode.
3-3. EDGING CONVERSION
1. Grip shaft firmly.
2. Push red button (A) forward, and rotate handle assembly until an audible click is heard (Figure 3-3).
4 - OPERATING INSTRUCTIONS
4-1. CONNECT THE CORD
1. Ensure the cord is NOT plugged into a receptacle before this procedure.
2. Make a loop with 8" - 10" (20 - 25cm) of the end of the extension cord.
All manuals and user guides at all-guides.com
3