Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Add Engine Oil
1.
Place pressure washer on a flat, level surface.
2.
Clean area around oil fill and remove oil fill cap/dipstick.
3.
Check oil level as described in Checking Oil Level.
4.
If needed, slowly pour oil into oil fill opening. Pause to
permit oil to settle. Fill to upper limit mark on dipstick.
DO NOT overfill.
NOTICE
Overfilling with oil may cause the engine to not start, or
hard starting.
• DO NOT overfill.
• If over the FULL mark on dipstick, drain oil to reduce oil level to
FULL mark on dipstick.
5.
Replace oil fill cap/dipstick and fully tighten.
Changing Engine Oil
Change engine oil after the first 5 hours and every 50 hours
thereafter. If you are using your pressure washer under
extremely dirty or dusty conditions, or in extremely hot
weather, change oil more often.
Avoid prolonged or repeated skin contact with used motor
oil.
• Used motor oil has been shown to cause skin cancer in certain
laboratory animals.
• Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Change oil while engine is still warm from running, as
follows:
1.
Drain fuel tank by running pressure washer until fuel
tank is empty.
2.
Disconnect spark plug wire and keep it away from spark
plug.
3.
Clean area around oil fill, remove oil fill cap/dipstick.
Wipe dipstick clean.
4.
Tip your pressure washer to drain oil from oil fill into a
suitable container making sure you tip your unit away
from spark plug. When crankcase is empty, return
pressure washer to upright position.
5.
Slowly pour recommended oil (approximately 18 oz.)
into oil fill opening. Pause to permit oil to settle. Fill to
upper limit mark on dipstick.
6.
Replace and tighten dipstick.
7.
Wipe up any remaining oil.
8.
Reconnect spark plug wire to spark plug.
CAUTION
Service Air Cleaner
Your engine will not run properly and may be damaged if you
run it with a dirty air cleaner.
Clean the air cleaner once every 3 months or 25 hours of
operation, whichever comes first. Replace the air cleaner
every two years or 250 hours, whichever comes first. Service
more often if operating under dirty or dusty conditions.
Replacements are available at your local Sears service center.
To service the air cleaner, follow these steps:
1.
Press latch tabs (A) on top of air cleaner cover (B), and
remove cover.
D
E
2.
Carefully remove air cleaner (C) from base (D).
3.
Clean air cleaner by tapping it several times on a hard
surface to remove dirt, or blow compressed air (not to
exceed 30 psi) through air cleaner from clean side that
faces engine.
NOTE: NEVER try to brush off dirt. Brushing will force dirt
into the fibers.
4.
Wipe dirt from air cleaner body and cover using a moist
rag. Be careful to prevent dirt from entering air duct (E)
that leads to the carburetor.
5.
Install clean (or new) air cleaner in base. Air cleaner
must fit securely in base.
6.
Reinstall air cleaner cover.
NOTE: You can purchase new air filter elements by calling
1-800-4-MY-HOME (469-4663).
Service Spark Plug
Service the spark plug every 100 hours of operation or
yearly, whichever occurs first. Replace the spark plug every
two years or 250 hours, whichever comes first.
1.
Disconnect the cap from the spark plug and clean area
around spark plug.
2.
Remove and inspect spark plug.
3.
Replace spark plug if electrodes are worn, or if insulator
is cracked or chipped.
19
C
B
A
A
Publicidad
Capítulos
Tabla de contenido
