Silverline 254155 Manual Del Usuario página 7

254155
Inspection procedures
• The following procedure helps detect defects potentially resulting in
degradation and/or weakening of karabiners:
1. Inspect for missing or altered parts. Refer to the image in 'Product
Familiarisation' for identification. Verify each item is present and has
not been tampered with
2. Inspect the entire karabiner for cracks, nicks or breaks in the metal.
Inspect every millimetre
Note: If necessary, clean before inspection, to be able to detect even
small hairline cracks.
3. Inspect for deformation, bents or dented parts. Open the Gate (4)
and inspect the nose of the karabiner for signs of wear, distortion or
damage
4. Inspect the metal surface for any signs of corrosion. Steel karabiners
may show red dust as evidence of corrosion, aluminium karabiners
may develop pitting or scales
5. Inspect for heat damage, which can usually be seen as discoloration or
darkening of the metal surfaces
6. Perform a functional test: The locking mechanism must move easily,
and the karabiner must fully open and close smoothly and easily. When
locked, the Gate MUST NOT open under pressure from any direction
• Inspect all other components or subsystem of the fall arrest equipment
according to manufacturer's instructions
• Record inspection date and results in a dedicated service record (see
end of this manual)
Note: Refer to 'Service life and product obsolescence' if any damage or
Cleaning
Note: Correct cleaning is essential to ensure integrity of all safety
equipment. Follow the cleaning instructions below without deviation.
• Clean the karabiner by wiping it with a soft, lightly oiled cloth
• If this is not sufficient, use warm water with a mild pH neutral (pH 7)
detergent, to clean off any foreign matter. Dry thoroughly and lubricate
moving parts with a suitable spray lubricant
• DO NOT under any circumstances use any abrasive materials, acids,
basic detergents or solvents
• Disinfect parts that come into contact with the operator's skin,
using a disinfectant suitable for the material of the equipment
(see 'Specification'). Strictly follow the disinfectant manufacturer's
recommendations and procedures
• ALWAYS allow the equipment to dry naturally, and keep it away from
open fire or any other heat source
Note: This also applies to equipment that has become wet during use.
Lubrication
• Occasionally apply a small amount of a suitable spray lubricant to the
gate mechanism of the karabiner and hook. Afterwards, perform a
thorough inspection as described in 'Inspection procedure'
Transport
• ALWAYS transport this equipment inside a dedicated bag or suitable
container that protects it from mechanical damage and shields the
equipment from high temperatures, humidity, UV rays and chemicals
Storage
• Store this tool carefully in a secure, dry place out of the reach of
children
• Store at moderate temperature and humidity, away from direct
sunlight or chemicals, inside a dedicated, UV-proof bag or container
• Never place heavy objects on top of this equipment
Disposal
Service life and product obsolescence
WARNING: Fall arrest gear is designed to arrest a fall from height ONLY
ONCE! If subjected to an arrested fall, the gear must be withdrawn from
service and rendered unusable.
Note: The date on which the product is removed from the original
packaging for the first time becomes the 'date of first use', which should
be recorded on the Inspection Record (see end of this manual). The
specified working life begins from this point.
• This equipment is subject to a maximum working life of 5 years from
the recorded date of first use, providing the product has been correctly
stored, maintained and subjected to regular inspections by a trained
and competent person
• New equipment may be stored for a maximum of 5 years from the
date of manufacturing as indicated on the product, and will still give
the potential 5-year working life – providing it remains in the original
manufacturer's packaging
Note: Other reasons why the product may be considered obsolete
include, but are not limited to, changes of applicable standard, regulations
or legislation, development of new techniques, or incompatibility with
other equipment.
WARNING: Remove fall arrest equipment from service if:
• it has been used to arrest a fall
• any damage is present
• identification is not evident (permanent markings are not legible or
have been damaged/removed)
• it exceeds its specified service life
• its full service history is unknown
• you have any doubt as to its integrity
www.silverlinetools.com
Scaffold Hook
7