Power Stroke PS80960 Manual Del Operador página 17

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

To disengage the lock out:
 Push the lock out down and into its original position.
To use the spray wand, start with the nozzle 1-2 ft. away
from the cleaning surface. Carefully approach the surface
just until the desired level of cleaning is achieved. If the spray
is too close it can damage the cleaning surface.
SELECTING THE RIGHT NOZZLE FOR THE JOB
See Figure 13.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. Refer to the Nozzle Selection Guide for more informa-
tion about which nozzle to choose.
WARNING:
NEVER remove nozzles without first turning off the en-
gine, relieving the water pressure in the trigger handle,
and locking the lock out on the trigger handle. NEVER
point the nozzle at your face or at others. The quick-
connect feature contains small springs that could eject
the nozzle with some force. Failure to follow these in-
structions could result in an eye injury or other serious
personal injury.
To connect a nozzle to the spray wand:
 Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
 Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
 Push the nozzle into the quick-connect collar until it clicks
in place and is secured properly.
To disconnect a nozzle from the spray wand once the
cleaning job is complete:
 Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
 Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
 Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar.
USING THE 5-IN-1 CHANGE OVER NOZZLE
There are five spray pattern settings located on the 5-in-1
Change Over Nozzle. To select a spray pattern, rotate the
spray selector to the desired setting. Refer to the Nozzle
Selection Guide for more information about which setting
to choose.
OPERATION
USING THE HIGH PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high pres-
sure hose prior to and during each use and do not allow
it to become kinked. The high pressure hose features an
outer covering that provides strength to the hose. If the
outer covering becomes damaged, stop using the hose
and replace it immediately. A kinked or damaged hose
can develop a high pressure leak and result in a possible
injection or other serious personal injury.
To prevent damage to the outer covering:
 Inspect the hose before every use.
 Fully unwrap and straighten hose before use.
 Do not allow the high pressure hose to be kinked.
 Keep hose away from hot surfaces and sharp edges.
 Do not pull unit by high pressure hose.
 Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figure 14 - 15.
As sold, this unit is designed for use with "downstream" pres-
sure washer detergents. To convert for use with "upstream"
detergents, contact an authorized customer service center
for more information.
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS. Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump
or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
 Remove the cap from the detergent container and pour
detergent in the container. Replace cap on container.
NOTE: The machine setting of this unit is 20:1, which usu-
ally allows the use of 1 gallon pressure washer detergent
without further dilution. Check your detergent instructions
to be sure additional dilution is not necessary.
 Install 5-in-1 Change-Over Nozzle (if necessary). Rotate
the spray selector on the nozzle to either the short range
detergent ( ) or long range detergent ( ) setting.
 Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
Page 13 — English

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido