Dust/Chip Extraction; Working Advice; Starting Operation - Bosch PMF 180 E Multi Manual Original

OBJ_BUCH-345-007.book Page 14 Wednesday, April 20, 2011 8:07 AM
14 | English
Sanding disc Material
– Paint
– Varnish
– Filling compound
– Filler
White quality

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Connecting the Dust Extraction
For sanding, always connect dust extraction.
Place a vacuum hose 4 (accessory) onto the vacuum connec-
tion 3. Connect the vacuum hose 4 with a vacuum cleaner (ac-
cessory). An overview for the connection of various vacuum
cleaners can be found at the end of these instructions.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Operation

Starting Operation

Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1 forward so
that the "I" is indicated on the switch.
To switch off the machine, push the On/Off switch 1 toward
the rear so that the "0" is indicated on the switch.
2 609 004 835 | (20.4.11)
Application
For sanding off paint
For sanding primer (e. g., for removing brush dashes,
drops of paint and paint run)
For final sanding of primers before coating
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
rate 2, you can preselect the required orbital stroke rate, even
during operation.
The required stroke rate depends on the material and the
working conditions and can be determined through practical
testing.

Working Advice

Before any work on the machine itself, pull the mains
plug.
Note: Do not cover off the venting slots 6 of the machine while
working, as this reduces the working life of the machine.
While working with HCS tools make sure that the covering of
the tools is undamaged.
Operating Principle
Due to the oscillating drive the application tool/accessory
swings up to 21000 times per minute for 2.8°. This allows for
precise work in narrow spaces.
Work with low and uniform application
pressure, otherwise, the working perform-
ance will decline and the application tool
can become blocked.
While working, move the machine back and
forth, so that the application tool does not
heat up excessively and become blocked.
Sawing
Use undamaged faultless saw blades only. Deformed,
blunt saw blades or saw blades that are otherwise dam-
aged can break.
When sawing light building materials, observe the stat-
utory provisions and the recommendations of the ma-
terial suppliers.
Plunge cuts may only be applied to soft materials, such
as wood, gypsum plaster boards, etc.!
Before sawing with HCS saw blades in wood, particle board,
building materials, etc., check these for foreign objects such
as nails, screws, or similar. If required, remove foreign ob-
jects or use BIM saw blades.
Grain size
coarse 40
60
medium 80
100
120
fine 180
240
320
Bosch Power Tools