Silverline 633770 Manual Del Usario página 11

633770
• Allow the blade to work steadily through the wood. It should not be
necessary to use force to make the saw cut. Slow cutting indicates a
blunt blade
• Do not allow the blade to touch the ground, or any object other than that
which you intend to cut
• Release the Throttle (5) as soon as the cut is complete
• Running the engine at full throttle without a load will cause rapid wear to
the engine, saw chain, and guide bar
Avoiding kickback
• Kickback is usually caused when the chain teeth near the tip of the
cutting bar 'bite' into a solid object. The resulting reactionary force may
make the saw violently accelerate up and back, towards the user
• The chain supplied with the chainsaw has been designed with kickback
reducing features. However, this does not mean that kickback will not
occur and you should be aware of kickback at all times. Careful use is
the best guarantee of safety
Maintenance
NOTE: Regular maintenance is essential to prolong the life of this power
tool. Without regular maintenance and proper storage the tool's working life
will diminish considerably.
• Always stop the engine, and allow to cool, before performing any
cleaning / maintenance
• Ensure that all screws and bolts are tightly fastened so that the unit can
be used safely
• Never use the power tool if any of the parts appear worn or broken. In
such case, consult your retailer
• Do not attempt to alter any of the components of this tool. To do so
would not only INVALIDATE YOUR WARRANTY, BUT MAY ALSO RESULT IN
DAMAGE TO THE UNIT, YOURSELF OR OTHERS IN THE VICINITY
Engine adjustment
When adjusted properly, the engine should idle smoothly and accelerate
without hesitation. The blade or spool should not move when the engine
is idling.
• To make the engine idle at a higher speed, rotate the Idling Adjustment
Screw (16) clockwise
• To make the engine idle at a lower speed, rotate the idle adjustment
screw anticlockwise
Cleaning the air filter (Fig D)
The Air Filter (12) should be cleaned regularly. To access the filter:
1. Unscrew and unclip the filter cover
2. Remove filter element from the housing and wash carefully using
household detergent and water
3. Dry the filter element, and liberally oil using a multi-purpose oil
4. Reassemble before using the tool
Checking the spark plug
• Remove the spark plug cap
• Clean any dirt and debris from around the plug
• Box spanner is supplied to remove plug for inspection
• If problem persists, contact your retailer or suitably qualified technician
Chainsaw – chain maintenance
• To extend the life of the saw chain and the efficiency of the saw, sharpen
the teeth regularly. This should only be carried out by a qualified and
experienced person
• If the teeth become worn through use, the chain should be replaced.
Consult your retailer or a suitably qualified and experienced technician
Drive shaft
• Apply grease periodically to the grease nipples on the chainsaw and
hedge trimmer, according to use – for example, at the beginning and end
of each season
25cc Multi-Head Garden System
Storage
• Allow the motor to cool fully before putting this tool in storage
• Store all parts of the tool in a clean, dry place away from heat and direct
sunlight. Ensure that all items are stored where children cannot get
access to them
• Never store the unit where the fuel tank can be exposed to extreme heat,
or where petrol fumes could come into contact with flames or sparks
• Keep the storage area clear of debris and possible tripping hazards
• Make sure all heads are clean and that the protective sleeves are in
place
Extended Storage
If you are putting the tool into extended storage, in addition to the items
listed in Storage above:
• Dilute a little household detergent in warm water and, using a damp
cloth, clean the plastic housings on the main body.
• Drain all fuel from the Fuel Tank (14) safely and make sure the fuel cap is
properly fastened in place
• Remove the spark plug and pour one teaspoon of clean oil into the spark
plug cylinder. Replace and reconnect the spark plug
• With the ignition off, pull the starter handle slowly to coat the engine
with oil
Drainage and Disposal
• If you need to drain fuel from the tank, do this outdoors and only when
the motor is cool
• To respect the environment, do not dispose of any fuel or oil drained
from the machine into the drainage system or ground. Local service
stations and recycling sites have proper facilities for the disposal of such
materials and only these locations should be used to dispose of such
products. If you do not know the location of your nearest depot, contact
your local authority for information
www.silverlinetools.com
11