Technical Parameters; Other Information - Elko EP SOU-3 Guia De Inicio Rapido

Technical parameters

Supply
Supply terminals:
Supply voltage:
Input (apparent / loss):
Max. dissipated power
(Un + terminals):
Tolerance of supply voltage:
Setting the scale level of lighting
Function twilight switch
- range 1:
- range 2:
- range 3:
Function light switch
- range 1:
- range 2:
- range 3:
Setting function
Level of light-slight:
Slight setting
of light level:
Time delay t:
Delay setting t:
Output
Output contact:
Rated current:
Switching output:
Peak current:
Switched voltage:
Mechanical life:
Electrical life:

Other information

Operation temperature:
Storing temperature:
Electrical strengh:
Operation position:
Protection degree:
Overvoltage cathegory:
Pollution level:
Max. cable size (mm 2 ):
Suggested power-supply cable:
Dimensions:
Weight:
Standards:
SOU-3
L - N
AC 230 V / 50 .. 60 Hz
max. 6 VA / 0.7 W
2.5 W
- 15% .. +10%
by jumper J2
1 ... 10 Lx
10 ... 100 Lx
100 ... 1.000 Lx
100 ... 1.000 Lx
1.000 ... 10.000 Lx
10.000 ... 100.000 Lx
by jumper J3
0.1 ... 1 x range
potenciometer
0 / 1 min. / 2 min.
by jumper J1
1x NO - SPST (AgSnO )
2
12 A / AC1
3000 VA / AC1, 384 W / DC
30 A / < 3 s
250 V AC / 24 V DC
3 x 10 7
5
0.7 x 10
-30 °C to +60 °C (-22 °F to 140 °F)
-30 °C to +70 °C (-22 °F to 158 °F)
4 kV (supply-output)
sensor-side down or on the sides
IP65
III.
2
max. 1x 2.5, max. 2x 1.5 /
with sleeve max. 1x 2.5 (AWG 12)
CYKY 3x2.5 (CYKY 4x1.5)
96 x 62 x 34 mm (3.8˝ x 2.4˝ x 1.3˝)
117 g ( 4.1 oz.)
EN 60255-6, 61010-1
Function
actual
illumination level
setup
illumination level
L - N
15 - 18
t
15 - 18
Warning
The device is constructed to be connected into 1-phase main and must be installed in
accordance with regulations and norms applicable in a particular country. Installation,
connection and setting can be done only by a person with an adequate electro-technical
qualifi cation which has read and understood this instruction manual and product
functions. The device contains protections against over-voltage peaks and disturbing
elements in the supply main. Too ensure correct function of these protection elements
it is necessary to front-end other protective elements of higher degree (A, B, C) and
screening of disturbances of switched devices (contactors, motors, inductive load etc.) as
it is stated in a standard. Before you start with installation, make sure that the device is
not energized and that the main switch is OFF. Do not install the device to the sources of
excessive electromagnetic disturbances. By correct installation, ensure good air circulation
so the maximal allowed operational temperature is not exceeded in case of permanent
operation and higher ambient temperature. While installing the device use screwdriver
width approx. 2 mm. Keep in mind that this device is fully electronic while installing.
Correct function of the device is also depended on transportation, storing and handling.
In case you notice any signs of damage, deformation, malfunction or missing piece, do
not install this device and claim it at the seller. After operational life treat the product as
electronic waste.
2 / 2
t
t
t t
solid
hysteresis
12%