Publicidad
Idiomas disponibles
Idiomas disponibles
NFC STANDALONE ACCESS CONTROL MODULE
SAFETY PRECAUTIONS
Always disconnect the power supply before installing or making modifications to the devices.
-
-
The fitting and handling of these devices must be carried out by
The wiring must run at least 40 cm. away from any other wiring.
-
-
On the power supply unit:
Do not overtighten the screws on the connector.
w
Install the power supply unit in a dry protected location free from the risk of dripping or splashing
w
water.
wAvoid locations that are humid, dusty or near heat sources.
wEnsure that the air vents are free from obstruction so that air can circulate freely.
wTo avoid damage, the power supply unit must be firmly secured in place.
wTo prevent electric shock, do not remove the cover or handle the wires connected to the
terminals.
CHARACTERISTICS
( )
*
-
NFC access control module (Golmar proximity cards
-
Can be combined with Nexa Modular panels.
-
Basic configuration using the SW1 DIP switch or Master card
-
Advanced configuration and management of the NFC access control. Mobile with NFC and AC
Manager app required (Android only), see the TAC Manager manual (code 50124945).
(Consult our technical service department).
-
Enables the user to manage the residents' card
access control via mobile. Mobile with NFC and OpenGo app required (Android only), see the
TOPENGO manual (code 50124946). (Consult our technical service department).
-
Status LEDs and tones.
INSTALLATION OF THE NFC ACCESS CONTROL
( )
*
1850
1650
1450
NCEV-90CS embedding box dimensions:
99(W) x 132.5(H) x 56.5(D) mm.
DESCRIPTION OF THE NFC ACCESS CONTROL
( )
*
( )
Description of the module:
*
The wiring terminals are located at the back of the module and
correspond to the following connections:
( )
For more information, see the TKIT N4502 NFC user manual (code
*
https://doc.golmar.es/search/manual/50123711
authorised personnel
.
/ key tags
).
/ key tag
.
/ key tag
to activate the lock release of the NFC
Embedding box.
Frame + EL4502/NFC module.
Panel.
Clip-on covers.
~, ~ :
power supply.
NA1 :
normally open output relay 1.
C1 :
common relay 1.
NC1 :
normally closed output relay 1.
NA2 :
normally open output relay 2.
C2 :
common relay 2.
NC2 :
normally closed output relay 1.
P :
panic output.
_
:
negative.
PL1 :
input for external button relay 1.
PL2 :
input for external button relay 2.
50123711).
Continued overleaf.
2
NFC STANDALONE ACCESS CONTROL MODULE
Continued from previous page.
( )
Description of the JP1 jumper:
*
Located to the right of the terminal strip.
P L
Normal operation, alarm not activated.
1 P
L 2
Tamper alarm mode is activated. In this mode, a constant audible
( )
Description of the self-testing LEDs:
*
The two-colour (red and green) self-testing LED is located on the top left-hand side of the front of the
module.
Red / Green
Programming
( )
Description of the tones:
*
Operation
Duration
Correct access
2 rapid tones
Incorrect access
1 long tone
Card programmed
2 rapid tones
Card deleted
2 rapid tones
Alarm activated
1 constant tone
BASIC PROGRAMMING USING THE SW1 DIP SWITCH
( )
*
NFC standalone access control:
Configuration of the NFC standalone access control allows access to the building by
waving a residents' card/
Add residents' cards/ key tags: set DIP switch 3 to ON, the LED on the
front will blink (red). Then wave all of the new NFC/US cards/ key tags
(Golmar) that you wish to add over proximity reader EL4502/NFC one by one, the
module will emit 2 tones and the LED will light up (green) for one second every time a
residents' proximity card/ key tag is memorised or the LED will blink (red) if the card/
key tag has already been memorised. Up to 2,000 cards/ key tags can be memorised.
Note: The module will emit an error tone and the green LED will light up to warn of
when the memory is full.
To exit "Add residents' cards/ key tags" mode, set DIP switch 3 to OFF, the LED on the
front (red) will turn off.
Remove all residents' cards/ key tags: set DIP switches 1 and 3 to ON, the LED on
the front will blink (red). Then press programming button P1 for 5 seconds, the LED
will blink rapidly (red); after 5 seconds, the LED will light up (green) for 1 second and
the module will emit 2 short tones indicating that the process has been carried out
successfully.
To exit "Remove all residents" cards/ key tags' mode, set DIP switches 1 and 3 to OFF,
the LED on the front (red) will turn off.
( )
For more information, see the TKIT N4502 NFC user manual (code
*
https://doc.golmar.es/search/manual/50123711
alarm and the "P" panic output (3 seconds every minute) are
activated.
Operation
Red LED
Green LED
Normal
Off
Standby
Correct access
Off
On (1.5 seconds)
On (1.5 seconds)
Incorrect access
With SW1 DIP
Slow blink
With Master card
On
Off
On (1.5 seconds)
Card programmed
mode
Rapid blink
Card already exists
Deleting cards
Rapid blink
Card deleted
Off
On (1.5 seconds)
Memory full (error)
Off
( )
Description of the SW1 DIP switch:
*
The NFC access control
It is located on the top right-hand side of the
module features an
internal buzzer for
( ) 1
reproducing operating
SW1
tones.
P1
key tag
(Golmar) over the EL4502/NFC proximity reader.
3
Off
Off
Off
Off
Off
Off
On
back of the module. It allows
us to add/remove cards and
configure the activation times
of Relay 1 and Relay 2.
( ) 1
Factory setting.
SW1
P1
50123711).
Continued overleaf.
Publicidad
