Owner's Manual
LED Indoor Lighting Fixture
Installation Instructions
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a
period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or
implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration of
components, nor does it cover damages caused through abuse, improper installation, surges in electric
current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many
years of beauty and service. For questions and comments, please visit
www.westinghouselighting.com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any
packing materials.
NOTE: THIS FIXTURE IS SUITABLE FOR USE WITH DIMMABLE SWITCHES, SEE BELOW FOR LIST OF
COMPATIBLE DIMMERS.
r B
n a
d
DVCL-153P, MACL-153M-WH, PD-6WCL-WH, S-603PG,
DVCL-153PR-WH, MRF2-6CL-WH, PD-10NXD-WH,
Lutron
DVCL-253P-WH, TGCL-153P, LGCL-153PLH, SCL-153P,
CTCL-153P-WH, S-600P-WH, MACL-153PLH-WH
Leviton
CD-C22-06672-12A, CD-R00-RNL06-12
Not recommended for use with motion sensors, light sensors, timers or any other external controls.
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with state and local electrical codes, it is recommended that you consult with
a qualified electrician.
3. Do not use in wet locations, use indoors only.
4. Non-replaceable LEDs.
5. Caution: LEDs emit bright light. Avoid looking directly into the light source for prolonged periods to
avoid eye damage.
6. Not to be used with a dimming circuit or any other electronically controlled switch.
M
o
d
e
# l
D
M I
M
INSTALLATION STEPS
W-578
032818
1. Drill hole in ceiling and prepare supply wires. Install
and unshield the line feed cable 6'' (15 cm) and strip
wires 5/8'' (1.6 cm). Bring supply power into junction
box through knockout. (Fig. 1)
2. Open the lid of the junction box. Use the wirenuts to
match the white wire from the line feed with the white
wire of the junction box. Match the black wire from the
line feed with the black wire of the junction box. Match
the copper wire from the line feed and with the green
wire of the junction box. (Fig. 2)
3. Route junction box through cut-out and connect
recessed LED pannel to junction box with the quick
connector. (Fig. 3)
4. Compress the springs and push the fixture into the
opening. It is easier to do one spring at a time. (Fig. 4)
N I
G
R
A
N
G
E
CLEANING AND CARE
10-100%
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean
this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lacquer
which gives maximum protection against the weather. However, in time the brightness of the brass
will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass fixture looking
new for years to come, regularly apply a good quality, non-abrasive car wax to all metal surfaces,
giving the fixture an extra protective covering.
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
50950, 50970, 50990, 51010:
MIN.
4.25''( 10.8 cm)
4.38'' ( 11.1 cm)
MAX.
4.5'' (
11.4 cm)
51030, 51070, 51090, 51110:
MIN.
6.14''( 15.6 cm)
6.22'' ( 15.8 cm)
MAX.
6.30'' (
16 cm)
Fig. 1
Maximum of 2 line feed
Fig. 2
in the junction box.
Fig. 3
Fig. 4
www.westinghouselighting.com
All rights reserved.
Made in China