Alarm Setting - Caliber HCG 008Q Manual Del Usuario

MANUAL
Precautions
Points to observe for safe usage
Read this manual carefully before using this item and its components.
They contain instructions on how to use this product in a safe and
effective manner. Caliber Europe BV cannot be responsible for problems
resulting from failure to observe the instructions in this manual.
Turn off the device immediately in case of a problem.
Failure to do so may cause personal injury or damage to the product.
Return it to your authorized Caliber Europe BV dealer for repairing.
Product cleaning.
Use a soft dry cloth for periodic cleaning of the product. For more
severe stains, please dampen the cloth with water only. Anything else
has the chance of dissolving the paint or damaging the plastic.
Temperature.
Ensure that the ambient temperature is between 0°C and +45°C
before turning on the device.
Below the descriptions of the features/options of the HCG 008Q. The number between the "(...)" refers to the
key or c onnections on the unit. The illustrations can be found in the front of this manual.
Connection and clock set
• Plug the adapter into a 100~240V AC outlet and the other end in the DC in (21).
• The electronic clock will turn on and the clock shows "0:00".
• P ress the [SET/MEM] button (3) and the hours will start flashing, use [DOWN/UP] (6/7) to set.
• P ress the [SET/MEM] button (3) again and the minutes will start flashing, use [DOWN/UP] (6/7) to set.
• Press [SET/ MEM] (3) again to choose between 24HR/12HR time indication, use [DOWN/UP] (6/7) to set.
• Press the [SET/MEM] button (3) again and you can set the seconds, using the [DOWN/UP] (6/7).
• After setting to the correct time, either press [SET / MEM] button (3) again, or just leave it for 5 seconds.
• To change the current time, the radio must be switched OFF – to turn it OFF, hold the [MODE] button (1) for 2
sec. and follow the steps above to adjust the time.

Alarm setting

This product features convenient dual alarms. Each alarm function can be set independently, with a choice
of Wake To Radio, buzzer or AUX-in. If either alarm is set to Wake To Radio, please remember to select the
desired band, station and volume level before turning off the radio. If either alarm is set to Wake LINE (AUX-in),
please remember to connect a (playing) source.
To set the alarm time, the Radio must be turned OFF. To turn it OFF, hold the [MODE] button (1) for 2 sec.
• P ress [ALARM] (2) and the AL1 (10) LED indicator + the hours start flashing. Use [DOWN/UP] (6/7) to set.
• P ress [ALARM] (2) again and the minutes will start flashing. Use [DOWN/UP] (6/7) to set.
• Press [ALARM] (2) again to choose between your wake-up source using [DOWN/UP] (6/7):
ON > wake-up to buzzer / ON + FM indicator (15) > wake-up to FM radio / ON + AUX indicator (16) > wake-up
to LINE input source / OFF
• After your choice, wait 5 sec. for the unit to switch to the current time. When set OK the AL1 LED (10) is lit.
To use a second alarm, you must run through the steps of setting AL1 first. After the last step (see above) press
[ALARM] (2) again to enter the setting of AL2, then the AL2 indication LED (11) will be flashing.
Use the same steps as above to set the alarm.
When the Alarm sounds, you can either:
• Press [MODE] button (1) once to switch off the alarm. You can see that the alarm indicator is still on, showing
that the alarm function is still activated and will sound the next day.
• Press the [SNOOZE] button (4) to temporarily turn the alarm off for 9 minutes.
• To disable the alarm completely, set your alarm to OFF (see steps at "Alarm setting').
Notes:
- T he alarm 1 (or 2) indicator will flash on the display when the alarm sounds.
- I f a later alarm sounds when the earlier alarm is still sounding, the first alarm will take priority.
- I f a later alarm sounds when the earlier alarm is in snooze, the later alarm will take priority and cancel the
snooze function of the earlier alarm automatically.
Maintenance.
If you have problems, do not attempt to repair the unit yourself.
Return it to your Caliber Europe BV dealer for servicing.
Placement.
Place the product on a flat surface. Provide enough space
around the product for sufficient ventilation.
Heat.
Do not locate the appliance in the vicinity of a heat surface or
in direct sunlight.