Technical Parameters - Elko EP iNels ADC3-60M Manual De Instrucciones

Technical parameters

Input
Analog inputs:
Number of inputs:
Galv. separation from
inner circuits:
Diagnostic:
sensor or overload of Uref output) by the applicable
Common terminal:
Converter resolution:
Input resistance
- for voltage ranges:
- for current ranges:
Voltage (U):
Types of inputs /
Current (I):
measuring ranges*:
Outputs of the Uref1 and Uref2 voltage
Voltage** / current of Uref1:
Voltage** / current of Uref2:
Communication
Installation BUS:
Unit status indication:
Power supply
Supply voltage / tolerance:
Dissipated power:
Rated current:
Connection
Terminal:
Operating conditions
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Design:
Dimensions and weight
Dimensions:
Weight:
* Selectable for each input/output individually by confi guration in the user program iDM3. Min.
supply voltage 24 V DC must be respected when confi guring 15 V DC and 100 mA consumption.
** According to load Uref output.
TECHNICAL SUPPORT | E-mail: support@inels.com | Mobil: +420 778 427 366 | Tel.: +420 573 514 276, +420 573 514 211 | Fax: +420 573 514 227 | www.inels.com
Made in Czech Republic
ADC3-60M
6x voltage, current or temperature input
6
no
indication (exceeding the range, interruption of a
red LED
COM
14 bits
approx. 150 kΩ
100 Ω
0 ÷ +10 V (U); 0 ÷ +2 V (U)
0 ÷ +20 mA (I); 4 ÷ +20 mA (I)
Temperature: input at ext. temperature sensor
TC, TZ see accessories / according to used sensor
from -30°C to 125°C
10 or 15 V DC / 100 mA
10 V DC / 20 mA
BUS
green LED RUN
27 V DC, -20 / +10 %
max. 1 W
100 mA (at 27V DC), from BUS
max. 2.5 mm 2 / 1.5 mm 2 with sleeve
-20 .. +55°C
-30 .. +70°C
IP20 device, IP40 mounting in the switchboard
II.
2
any
into a switchboard rail to DIN EN 60715
3-MODULE
90 x 52 x 65 mm
112 g
ELKO EP, s.r.o. | Palackého 493 | 769 01 Holešov, Všetuly | Czech republic | e-mail: elko@elkoep.com
Warning
Before the device is installed and operated, read this instruction manual carefully and with full
understanding and Installation Guide System iNELS3. The instruction manual is designated for
mounting the device and for the user of such device. It has to be attached to electro-installation
documentation. The instruction manual can be also found on a web site www.inels.com. Attention,
danger of injury by electrical current! Mounting and connection can be done only by a professional
with an adequate electrical qualifi cation, and all has to be done while observing valid regulations.
Do not touch parts of the device that are energized. Danger of life-threat! While mounting,
servicing, executing any changes, and repairing it is essential to observe safety regulations, norms,
directives and special regulations for working with electrical equipment. Before you start working
with the device, it is essential to have all wires, connected parts, and terminals de-energized. This
instruction manual contains only general directions which need to be applied in a particular
installation. In the course of inspections and maintenance, always check (while de-energized) if
terminals are tightened.
2/2