Milwaukee 3521-20 Manual Del Operador página 4

SPECIFICATIONS
Cross Line ................................................ 3521-20
Cross Line and Plumb Points ................. 3522-20
USB Input Volts .............................................. 5 DC
USB Input Amps ..................................... 0.1 - 2.1 A
Output Volts .................................................... 4 DC
Output Amps ....................................................2.1 A
REDLITHIUM USB Batteries
®
Volts ................................................................ 4 DC
Power Supply Cat. No. ....................... 48-59-1202
Laser............................................................Class 2
Lines Max Power ................................. P
Points Max Power............................... P
Frequency....................................................10 KHz
Pulse Duration Normal Mode ................. T
Pulse Duration Power Save.................... T
Wavelength.......................................... 510-530 nm
Lines Beam Divergence ................................. 1 rad
Points Beam Divergence .......................... 0.5 mrad
Storage Temp .................................... -4°F to 120°F
Working Range .................................................100'
Range with Detector .........................................165'
Accuracy ...............................................±1/8" @ 33'
Settle Time ......................................... < 3 Seconds
Tripod Mount ............................................... 1/4"-20
Ingress Protection............................................ IP54
Drop Rating .......................................................1 m
Leveling ............Auto ±°4 side to side, front to back
Operating Temperature
Battery and Charger ........................ 40°F to 104°F
Battery and Tool ............................... 14°F to 104°F
BATTERY
To reduce the risk of fire, personal
WARNING
injury, and product damage due to
a short circuit, never immerse your tool, battery
pack or charger in fluid or allow a fluid to flow
inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., can
cause a short circuit.
Maintenance and Storage
Do not expose your battery or cordless tools to water or
rain, or allow them to get wet. This could damage the
tool and battery. Do not use oil or solvents to clean or
lubricate your battery. The plastic casing will become
brittle and crack, causing a risk of injury.
Store batteries at room temperature away from mois-
ture. Do not store in damp locations where corrosion
of terminals may occur. As with other battery types,
permanent capacity loss can result if the pack is stored
for long periods of time at high temperatures (over 120°
F). MILWAUKEE Li-Ion batteries maintain their charge
during storage longer than other battery types. After
about a year of storage, charge the battery as normal.
WARNING
battery pack even if it is damaged, dead or com-
pletely discharged. When burned, toxic fumes
and materials are created.
Disposing of MILWAUKEE Li-Ion Battery
MILWAUKEE Li-Ion batteries are more environmen-
tally friendly than some other types of power tool
batteries. Always dispose of your battery according
to federal, state and local regulations. Contact a
recycling agency in your area for recycling locations.
Even discharged batteries contain some energy.
Before disposing, use electrical tape to cover the
≤ 7 mW
AVG
terminals to prevent the battery from shorting, which
≤ 1 mW
AVG
could cause a fire or explosion.
≤ 70 µs
RBRC Battery Recycling Seals
P
≤ 50 µs
The RBRC™ Battery Recycling Seals (see "Symbol-
P
ogy") on your batteries indicate that MILWAUKEE
has arranged for the recycling of that battery with
the Rechargeable Battery Recycling Corporation
(RBRC). At the end of your battery's useful life,
return the battery to a MILWAUKEE Branch Office/
Service Center or the participating retailer nearest
you. For more information, visit the RBRC web site
at www.rbrc.org.
WARNING
chargeable tool. Other types of batteries may
cause personal injury and damage.
1. Twist the battery cap and remove.
2. Line up the arrow on the battery with the arrow in
the compartment and fully insert the battery.
3. Replace the cap and twist to secure.
When the tool is turned on under battery power only, the
remaining battery life is displayed:
Green Solid: 50-100% remaining
Yellow Solid: 11-49% remaining
Red Solid: 3-10% remaining
Red Flashing: 0-3% remaining LOW POWER MODE
To indicate LOW POWER MODE, the laser beams
will dim, and the green laser mode indicator pulse,
and the laser beams will blink quickly 3 times, fol-
lowed by 4 seconds of solid on (repeating). Charge
the battery.
To charge the battery:
1. Plug your USB cable into a power source such as
an AC wall adaptor, computer, or car port.
2. Lift the rubber cover to expose the micro USB port.
Insert the micro USB plug into the micro USB port.
Users may experience longer charge times from
laptops and other power sources.
3. When the laser level is charged when OFF, the
indicator light will display the charging status:
Pulsing Red: Charging, 0-49% charged
Pulsing Yellow: Charging, 50-99% charged
Solid Green: 100% Charged.
4
To reduce the risk of injury or ex-
plosion, never burn or incinerate a
ASSEMBLY
Use and charge only REDLITHIUM
USB batteries in this USB re-
Inserting the Battery
Charging the Battery
®