Helios PROX Manual Del Usuario página 11

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

6. Learning of one transmitter
6.1 Learning of one transmitter through the learning key
HELIOS PROX control unit can be controlled by all transmitters of the series B.ROL 433 MHz with almost 2 keys and by the series CLARUS.
A little key is present on the card, it is called learning key.
a
b
a
b
1
1
Attention: the functionality of the button is true only with DIP4 in OFF. If the DIP4 is in ON the functionality of the button is inverted and
the button "a" or "a1" makes the closure while the button "b" or "b1" makes the opening.With the DIP4 on ON position, also the func-
tioning of the wired buttons is opposed as regards to what indicated in the silk-screen printing of the control unit.
6.2 Learning of the successive transmitters with a transmitter already learned
1.
Opening of the memory: in order to open the memory by transmitter, make reference to the instructions of the transmitter in possession.
Once opened the memory of the control unit, this one signals it turning on the red led.
2.
Press the key "a" or "a1" of the transmitter. The control unit memorizes automatically also the key "b" or "b1" and the key "c" for the series
CLARUS ("a" or "a1" as key "open", "b" or "b1" as key "close" and "c" as key "stop"). The control unit signals the memorization of the
channel with two blinking if the channel was not memorized and with one blinking if the channel was already learned.
3.
Once memorized the channel, the control unit goes back in normal functioning mode. If within twenty seconds no signal is transmitted, the
control unit automatically goes out from the learning mode.
Attention: the functionality of the button is true only with DIP4 in OFF. If the DIP4 is in ON the functionality of the button is inverted and
the button "a" or "a1" makes the closure while the button "b" or "b1" makes the opening.With the DIP4 on ON position, also the func-
tioning of the wired buttons is opposed as regards to what indicated in the silk-screen printing of the control unit.
6.3 Deletion of one transmitter from the memory of a control unit
PRESS the hidden
a
key "e"
a
PRESS at the same
time the hidden key
"e" + the key "a"
a
a
Attention: do not utilize this procedure in presence of more control units in function, because the opening of the memory
would happen for all the devices in which the channel is memorized. In this case cut off tension to the control units which
are not interested.
6.4. Total deletion of the memory and reactivation of the factory settings
It is possible to reset in every moment the values of factory by resetting the card. This operation brings also to the deletion of all the transmitters.
For the reset of the card it is sufficient:
1.
Cut off tension to the control unit
2.
Press the learning key and maintain it pressed while you give tension to the control unit . The 3 led blink one time then rest turned on.
3.
Keep on pressing the key until the red led do not turns off itself.
4.
Release the key. After this operation all the transmitters must be reinserted again and you must execute again the settings.
6.5 Reset of the parameters to the values of factory
This operation deletes all the parameters (automatic position of opening, alarms) without deleting all the transmitters and puts the control unit on
close position. To reset the parameters of the card to the values of factory is sufficient:
1.
Close the sunshade
2.
Press and keep on pressing the learning key until the alarm led blinks quickly (7 seconds)
3.
Release the key, the red led stops blinking. The reset has been executed.
6-1621095
rev.9
19-07-2012
1.
Press and release the little learning key present on the card; the red led turns on
2.
Press the key "a" or "a1" of the transmitter. The control unit memorizes automatically also
the key "b" or "b1" and the key "c" for the series CLARUS ("a" or "a1" as key "open", "b" or
"b1" as key "close" and "c" as key "stop"). The control unit signals the memorization of the
a
channel with 2 lightning of the red led if the channel was not memorized and one if the
c
channel was already learned.
3.
Once memorized the channel, the control unit goes back on normal functioning mode. If
b
no signal is transmitted within twenty seconds, the control unit goes out automatically
from the learning mode.
DELETION transmitter series B.RO:
b
Press the hidden key "e" present in the transmitter; the red led turns on. This operation is equivalent
1.
b
1
1
to press the LEARNING key, but without the necessity to access physically to the control unit.
e
2.
Press simultaneously for some second the hidden key and one key of the transmitter which you
must delete (ex. "e" + "a" , or "e" + "a1"). The control unit signals the happened deletion with 4
prolonged blinking, then the control unit goes back on normal functioning mode.
DELETION transmitter series CLARUS:
b
To execute the deletion of one channel or of the entire transmitter, you must access to the internal menu of
b
1
1
e
the transmitter. To do it, make reference to the instructions of the transmitter in possession.
ITA
ENG
FRA
ESP
DEU
POR
11 / 32

Publicidad

Tabla de contenido
loading

Tabla de contenido