Ryobi CCG-1801 Manual De Utilización página 6

Pistola de cola inalambrica
Ocultar thumbs Ver también para CCG-1801:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 18
EN
FR
DE
ES
IT
NL
WARNING
Always wear safety goggles or safety glasses with side
shields when operating products. Failure to do so could
result in objects being thrown into your eyes, resulting in
possible serious injury.
WARNING
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended can
result in serious personal injury.
This product will accept Ryobi One+ 18 V lithium-ion
battery packs and Ryobi One+ 18 V nickel-cadmium
battery packs.
WARNING
Always remove battery pack from the product when you
are assembling parts, making adjustments, cleaning, or
when it is not in use. Removing battery pack will prevent
accidental starting that could cause serious personal injury.
BATTERY PROTECTION FEATURES
Ryobi 18 V lithium-ion batteries are designed with features
that protect the lithium-ion cells and maximize battery life.
Under some operating conditions, these built-in features
may cause the battery and the tool it is powering to act
differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to stop
running. To reset the battery and tool, release the trigger
and resume normal operation.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and tool,
the battery pack is depleted. If depleted, the battery pack
will begin charging when placed on the lithium-ion charger.
TO INSTALL BATTERY PACK (NOT INCLUDED)
See fi gure 2.
■ Lock the switch trigger by sliding the switch lock up.
■ Place the battery pack on the tool.
■ Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured on the
tool before beginning operation.
PT
DA
SV
FI
NO
RU
English
PL
CS
HU
RO
LV
LT
When placing battery pack in the tool, be sure raised rib on
battery pack aligns with the bottom of the drill and latches
into place properly. Improper installation of the battery pack
can cause damage to internal components.
TO REMOVE BATTERY PACK (NOT INCLUDED)
See fi gure 2.
■ Lock the switch trigger by sliding the switch lock up.
■ Depress the latches on the side of battery pack.
■ Remove the battery pack from the tool.
STARTING/STOPPING THE CAULK GUN
See fi gure 3.
Before attempting to start the caulk gun, be sure the
switch lock is in the unlocked position.
■ To turn the caulk gun ON, depress the switch trigger.
■ To turn the caulk gun OFF, release the switch trigger.
LOCKING THE SWITCH TRIGGER
See fi gure 3.
The switch trigger of the caulk gun can be locked off using
the slide switch located below the switch trigger.
■ To lock the switch trigger, slide the switch lock up. This
will prevent the caulk gun switch trigger from being
depressed.
■ To unlock the switch trigger, slide the switch down.
This will allow the caulk gun switch trigger to be
depressed.
LOADING CAULK (NOT INCLUDED)
See fi gure 4-5.
Lock the switch trigger by sliding the switch lock up.
■ Using a utility knife, cut off the tip of the spout on a
standard 10 oz. tube of caulk. Cut the tip at a 45°
angle.
■ Remove as little as possible, taking into consideration
the size of the "bead" of caulk you need.
■ Check for a second inner seal at the base of the spout.
If found, insert the puncture tool inside the spout to
break the seal before using. If using a partially filled
tube, use the puncture tool to remove any hardened
material from the tip.
NOTE: An inner seal is usually found only in cardboard
caulk tubes.
2
ET
HR
SL
SK
EL
TR
CAUTION
UK

Publicidad

Tabla de contenido
loading

Tabla de contenido