Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Erase/Reset
• To erase users:
NOTE: Erasing a user will erase ALL stored fingerprints. User
does NOT need to reprogram to opener.
1. Open cover and wait until Ready
LED is lit.
2. Enrolled user must slowly and firmly
swipe fingerprint.
3. Press and hold the Enroll button for at
least 6 seconds. The Pass LED and Fail
LED will flash for 15 seconds. During
this time the Resend button is active.
After 15 seconds the Enroll and Ready
LEDs will light indicating fingerprints are
erased. The unit will return to Enroll
mode.
• To return unit to Factory Reset state:
NOTE: Factory reset state will erase ALL stored fingerprints.
This method should be used ONLY when an enrolled user is
not available as it requires user to reprogram unit to opener.
1. Open cover and wait until Ready
LED is lit.
2. Press and hold the Enroll button
until all LEDs turn off. Release
button.
3. Again press and hold the Enroll
button until the Ready and Enroll
LEDs are lit and not flashing.
Troubleshooting
• If no known enrolled users are available:
— The memory must be erased using the Factory Reset
process.
• If the unit does not recognize a swiped fingerprint:
— Ensure that the Ready LED is lit before you swipe.
— Ensure that fingerprint is swiped correctly (See Tips for
Success).
— Ensure that fingerprint is enrolled.
— Ensure that sufficient pressure is being applied to sensor
strip (do not press too hard).
— Ensure that the sensor and finger are not wet.
• If the unit is in Enroll mode at power up:
— Complete enrollment process for initial user.
— The initial enroll process failed (signalled by a lit Enroll
LED and Fail LED) and must be repeated.
• If enrolling new user and all LEDs flash and unit returns
to Ready mode:
— The memory is full. In order to add new user, the memory
needs to be erased. Refer to Erase User or Factory Reset.
• If the unit does not wake:
— A button may be stuck. Press Enroll and Resend buttons
to ensure free movement.
— The batteries may need to be replaced.
114A3408
• If the Fail LED flashes during use:
— The batteries need to be replaced.
NOTE: If sensor is dirty, user should wipe sensor with a clean
finger. It is recommended that the sensor be periodically
1
cleaned with a lint-free cloth dampened with alcohol.
ENROLL
The Battery
SEND
ENROLL
PASS
FAIL
READY
RETRY
2
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
3
The batteries should produce power for
at least one year. Replace when the
Fail LED flashes during use. The unit
requires 4 AAA batteries.
Dispose of old batteries properly.
1. Slide cover completely off.
1
2. Unscrew the two screws and
remove the battery cover.
ENROLL
3. Replace the batteries. Screw the
SEND
ENROLL
battery cover back on.
PASS
FAIL
READY
RETRY
4. Slide cover back into place.
2
3
Replacement parts:
Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41A6481
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
© 2007, The Chamberlain Group, Inc.
All Rights Reserved
WARNING
WARNING
Cover
Battery
Cover
Screws
SEND
PASS
READY
ENROLL
ENROLL
FAIL
RETRY
Publicidad
Tabla de contenido
