Tabla de contenido
Publicidad
4. Installation and Initial Startup
NOTE: Before installation, please inspect the unit. Be sure that nothing inside
the package is damaged.
Placement & Storage Conditions
Install the UPS in a protected area that is free of excessive dust and has adequate air flow.
Please place the UPS away from other units at least 20 cm to avoid interference. Do NOT
operate the UPS where the temperature and humidity is outside the specific limits.
EN
(Please check the specs for the limitations.)
Connect to Utility and Charging
Before initial use, please plug in the AC input cord to the wall
outlet and turn on the UPS for charging. For the best results,
suggest to charge the battery at least 8 hours before initial use.
Connect the Loads
Plug in the loads to output receptacles on the rear panel of the
UPS. Simply turn on the power switch of UPS unit, then devices
connected to the UPS will be protected by UPS unit.
Turn On/Off the Unit
CAUTION: NEVER connect a laser printer or scanner to the UPS unit. This may cause the
damage of the unit.
Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing
again the power switch.
Indicators & Alarm Table for Operation
Conditions
AC Mode
Battery Mode
Low battery at battery
Green LED flashing every second
mode
Fault
Alarm for
over-temperature
protection
8 hours
Visual Indicator
Green LED lighting
Green LED flashing every 10
Sounding every 10
seconds
Sounding every second
and Red LED lighting
Red LED lighting
Continuously sounding
Red LED flashing every 0.5
seconds
5. Important Safety Warning (SAVE THESE INSTRUCTIONS)
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and
humidity controlled indoor area free of conductive contaminants. (See the specifications for
the acceptable temperature and humidity range.)
CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents
and avoid exposing the unit to direct sunlight or installing the unit near heat emitting
appliances such as space heaters or furnaces.
CAUTION! Do not attach non-computer-related items, such as medical equipment,
life-support equipment, microwave ovens, or vacuum cleaners to UPS.
CAUTION! Do not plug the UPS input into its own output.
CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place
beverages or any other liquid-containing vessels on or near the unit.
CAUTION! In the event of an emergency, press the OFF button and disconnect the power
cord from the AC power supply to properly disable the UPS.
CAUTION! Do not attach a power strip or surge suppressor to the UPS.
CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is a must during
UPS installation in order to reduce leakage current below 3.5A.
Attention hazardous through electric shock. Also with disconnection of this unit from the
mains, hazardous voltage still may be accessible through supply from battery. The battery
supply should be therefore disconnected in the plus and minus pole at the quick connectors
of the battery when maintenance or service work inside the UPS is necessary.
CAUTION! Servicing of batteries should be performed or supervised by personnel
knowledgeable of batteries and the required precautions. Keep unauthorized personnel
away from batteries.
CAUTION! When replacing the batteries, use the same number and type of batteries.
CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery.
CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do not open or
mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes.
CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
CAUTION! A battery can present a risk of electric shock and high short circuit current. The
Alarm
following precaution should be observed before replacing batteries:
Off
1)
Remove watches, rings, or other metal objects.
2)
Use tools with insulated handles.
seconds
3)
Wear rubber gloves and boots.
4)
Do not lay tools or metal parts on top of batteries.
5)
Disconnect charging source prior to connecting or disconnecting batteries terminal.
Off
EN
Publicidad
Tabla de contenido
