Technical Data - Elta 905N2 Manual De Instrucciones

INSTRUCTION MANUAL
Dear customer,
Please read these Operating Instructions through carefully before connecting your device to the mains, in order to avoid
damage due to incorrect use. Please pay particular attention to the safety information. If you pass the device on to a third
party, these Operating Instructions must also be handed over.
DESIGN
1. Front protection guard
2. Cover cap
3. Rotor blade
4. Fixing ring
5. Rear protective guard
6 Speed buttons 0/1/2/3
7. Locking screw
8. Oscillation On/Off switch
9. Rotor shank and threads
10. Fan head
11. Screw
12. Power cord with power plug
13. Height adjustment
14. Telescopic tube
15. Cover
16. Pedestal
SAFETY INFORMATION
• Incorrect operation and improper use can damage the appliance and cause injury to the user.
• The appliance may be used only for it's intended purpose. No responsibility can be taken for any possible damage
caused through incorrect use or improper handling.
• Before connecting the appliance to the power source, check that the current and power match those given on the rating
plate.
• Do not put the appliance or the plug in water or any other liquid. However should the appliance accidentally fall into
water, unplug the appliance immediately and have it checked by a qualified person before using it again. Non-
observance could cause a fatal electric shock!
• Never attempt to open the housing yourself.
• Do not place any kind of object into the inside of the housing.
• Do not use the appliance with wet hands, on a damp floor or when the appliance itself is wet.
• Do not touch the plug with wet or damp hands.
• Check the cord and the plug regularly for any possible damage. If the cord or plug is damaged, it must be replaced by
the manufacturer or a qualified person in order to avoid a hazard.
• Do not use the appliance if it is dropped or otherwise damaged or if the cord or plug are damaged. In the case of
damage, take the appliance to an electrical repair shop for examination and repair if necessary.
• Never attempt to repair the appliance yourself. This could cause an electric shock.
• Do not allow the cord to hang over sharp edges and keep it well away from hot objects and naked flames. Remove the
plug from the socket only by holding the plug.
• For extra protection it is possible to fit the electric household installation with a fault current breaker with a rated
breaking current of not more than 30mA. Ask your electrician for advice.
• Make sure that there is no danger that the cord or extension cord may inadvertently be pulled or cause anyone to trip
when in use.
• If an extension cord is used it must be suited to the power consumption of the appliance, otherwise overheating of the
extension cord and/or plug may occur.
• This appliance is not suitable for commercial use nor for use in the open air.
• Never leave the appliance unattended while it is in use.
• Children cannot recognise the dangers involved in the incorrect use of electrical appliances. Therefore never allow
children to use household appliances without supervision.
• Always remove the plug from the socket when the appliance is not in use and each time before it is cleaned.
• Danger! Nominal voltage is still present in the appliance as long as the appliance is connected to the mains socket.
• Switch the appliance off before disconnecting from the mains.
• Never use the cord to carry the appliance.
All manuals and user guides at all-guides.com
9050N2 40CM STAND FAN
2 3 4 5 6 7
1
SPECIAL SAFETY INFORMATION
• The protective guard must be in place and locked when the unit is operating.
• Do not place any objects in the protective guard. Do not move the protective guard during operation.
BEFORE STARTING FOR THE FIRST TIME
• Remove all packing material.
• Clean the unit before using it for the first time (see CLEANING AND CARE).
ASSEMBLY
8
• Turn the cover cap (2) off in the direction LOOSEN from the rotor shank (9). Then remove the fixing ring (4) from the
9
threads (9) in the counter-clockwise direction. Set the rear protective guard (5) with the bulge on the fan head (10) in
10
such a manner, that the hollow tray fits on the fan head (10). Screw on the fixing ring (4) on the threads (9) turning it in
the clockwise direction.
11
• Now pull off the small safety hose from the rotor shank (9).
• Insert the rotor blade (3) on the rotor shank (9). The small pieces protruding from the rotor shank (9) must be fitted
precisely into the openings on the rear side of the rotor blade (3).
12
• Now secure the rotor blade (3) by rotating the cover cap (2) in the direction indicated by TIGHTEN.
• Fix the front protective guard (1) on the hooks on the rear protective guard (5). Secure the protective guards (1, 5)
against unintended opening by using the fixing screw. Slide the holder brackets over the edges of the protective guard
13 (1, 5).
• Engage the two parts of the pedestal (16) in such a manner that they form a cross (refer to the figure). Attach the
14
telescopic tube (14) to the pedestal (16) using the four screws supplied.
• You can use the cover (15) to conceal the screws.
15
• Now mount the fan head (10) on the telescopic tube (14). Set the height adjustment (13) of the telescopic tube (14) by
rotating counter-clockwise to loosen it. You can now reset the length of the telescopic tube (14) as desired. Then tighten
the telescopic tube (14) again by rotating the height adjustment (13) clockwise.
• Loosen the locking screw (7) and set the fan head (10) on the telescopic tube (14). Now you can tighten the locking
16
screw (7).
OPERATION
• Connect the main plug (12) to a suitable socket.
• You can set the desired speed by using the speed buttons (6) on the pedestal of the fan head (10):
0 = Unit Off
1 = Low speed
2 = Medium speed
3 = High speed
• You can set the fan at the desired angle by tilting the fan head (9) front or back. For this purpose, loosen the screw (11),
adjust the fan inclination and tighten the screw (11) again.
• When the unit is not going to be used further, press the speed button 0 (6) and pull out the mains plug.
• If you want the fan head (10) oscillate from left to right when the fan works, press the oscillation switch (8) in. If you
would like the direction of the fan to remain fixed, pull out the oscillation switch (8).
CLEANING AND CARE
• In addition to this, you must observe the safety instructions.
• Use a piece of cloth moistened with water and cleaning medium for cleaning the housing.
• If you want to clean the rotor blades (3), please remove the fixing screw from the protective guards (1, 5) first, open the
holder brackets and remove the front protective guard (1). Turn the cover cap (2) off in the direction LOOSEN from the
rotor shank (9). You can now remove the rotor blade (3) from the unit.
• Clean the rotor blade (3) using a lightly moistened cloth and some mild cleaning medium if necessary. Finally, wipe it till
dry. Reassemble the unit as described in ASSEMBLY.

TECHNICAL DATA

Operating voltage
Power consumption
GUARANTEE AND CUSTOMER SERVICE
Before delivery our devices are subjected to rigorous quality control. If, despite all care, damage has occurred during
production or transportation, please return the device to your dealer. In addition to statutory legal rights, the purchaser has
an option to claim under the terms of the following guarantee:
For the purchased device we provide 2 years guarantee, commencing from the day of sale. During this period we will
remedy all defects free of charge, which can be demonstrably attributed to material or manufacturing defects, by repair or
exchange.
Defects which arise due to improper handling of the device and malfunctions due to interventions and repairs by third
parties or the fitting of non-original parts, are not covered by this guarantee.
3
: 230V~ 50Hz
: 50 Watt
approved
4