Assistance Service - Peg-Perego VESPA Manual De Uso Y Mantenimiento

RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION!
The item is equipped with a brake system which
needs to be appropriately illustrated to the child by
an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
device will immediately disconnect the power. To
reset the device and restore the power supply,
release the accelerator until it has cooled (this may
take up to 60 seconds).
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

ASSISTANCE SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://global.pegperego.com/toys-site/support/
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and
valuable to us. We would be very grateful if, once
you have used the product, you would fill out the
CONSUMER SATISFACTION QUESTIONNAIRE
which you can find on the internet at:
www.pegperego.com, making any observations
or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
ASSEMBLY
1 • Turn the article upside down so that you can
work on the bottom of it. Remove the two
bearings from the axle.
2 • Position the stands as shown in the figure.
3 • Fasten the stands with the supplied screws.
4 • Attach the two decals to the body, as shown in
the figure.
5 • Before fitting the wheel, REMOVE THE SCREW
ON THE AXLE AND KEEP IT. You will need it
later to secure the handlebars, as shown in figure
14 (2).
6 • Put the front wheel on the axle, keeping the side
with the plastic bearing on the inside.
7 • Put a stud into the special tool, and fasten the
wheel in place, hammering it all the way down.
8 • Slip the fender bearing onto the axle and push it
all the way to the end (picture B). Note: The
bearing is shaped so that it can only be put on
the axle one way (see detail in picture A).
9 • Slip the fender onto the axle and fasten it to the
fender bearing, as shown in the detail.
10 • Push the lower steering bearing all the way into
its hole, taking care to line it up correctly.
11 • Attach the axle unit with the wheel to the front
of the vehicle and fasten the fender to the lower
steering bearing.
12 • Insert the upper steering bushing. Ensure that the
cable inside is in its housing, as shown in the
figure.
13 • Attach the 2 acceleration system connectors, as
shown in the figure.
14 • Attach the handlebars and fasten them with the
supplied screw.
15 • Stick the mirrors into their holes on the
handlebars and turn them outwards to fasten
them into place.
16 • Attach the foot mat, snapping it into the back
openings first and then the front openings
(bending the mat slightly). Press the central part
of the mat on both sides to fasten it securely.
17 • Lift the seat and place the carrier on the vehicle.
Fasten it with the four supplied screws.
18 • Lower the seat.
19 • Turn the clasp behind the seat to the position
shown in picture A. With the clasp in the position
shown in picture B, the seat can be opened.
20 • Attach the taillight sticker and snap the glass
cover into place.
21 • Attach the silver rear signal light stickers, and
snap the glass covers into place.
22 • Attach the silver front signal light stickers, and
snap the glass covers into place.
23 • To connect the cover and the bottom of the rear
cargo box, align the black hinges with the green
clasps as shown in the figure and squeeze
together until they engage with a "snap".
24 • Position the cargo box on the rear rack and
insert the black plastic screw into one of the two
holes based on the height of your child.
25 • Using a screwdriver, securely fasten the cargo
box to the rear rack.
26 • Lift the saddle and connect the electric system
plugs. After completing the procedure, always
remember to replace and secure the saddle. The
vehicle is ready for use.
VEHICLE CHARACTERISTICS AND USE
27 • THROTTLE GRIP: To start moving, turn the right
grip in the direction shown by the arrow. To slow
down, release the throttle.
28 • HORN BUTTON: Press this button to sound the
horn.
29 • Front carrier compartment.
30 • The kickstand is only for use when the training
wheels have been removed. NOTE: Please be
sure your child has developed an adequate sense
of balance on the scooter before removing the
training wheels. Show your child how to use
his/her foot to lower the kickstand into position
by pushing down and to raise it before riding by
pulling up.
31 • Rear carrier case. To open the cargo box, push in
on the button and at the same time pull up on
the cover. Maximum weight capacity of cargo
box: 3kg.
32 • OPTIONAL: Helmet
REPLACING THE BATTERY
33 • Remove the rear carrier case. Turn the lock
behind the saddle to release it. Lift the saddle.
34 • Remove the 3 screws on the battery holder and
disconnect the flat or damaged battery.
35 • Replace the battery, connect the plugs of the
new battery and secure the battery holder with
the screws.
36 • Replace and secure the saddle.
CHARGING THE BATTERY
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
37 • Disconnect electrical system plug A from battery
plug B, by pressing on the sides of both plugs.
38 • Plug the battery charger into an electrical outlet,
following the instructions for the battery charger.
Connect plug B to plug C from the battery
charger.
39 • When the battery has finished charging, unplug
the battery charger from the electrical outlet,
then disconnect plugs C and B.
40 • Connect plugs B and A, pressing until they snap
together. Always remember to lower and to
fasten the seat when you have finished working
under it.