Publicidad
37. Do not lift the water tank by the water mist outlet.
38. It is prohibited to insert metal chips, wire, needles and other foreign objects into the
product or into the housing gaps, otherwise it may cause electric shock or malfunction.
The device is designed to work in rooms with a temperature of 5-40 ° C and a relative
humidity of 80%.
DESCRIPTION OF THE DEVICE: ULTRASONIC HUMIDIFIER (picture A)
A1. Water mist outlet
A3. Base
A5. Water tank cover
A7. Water descaling filter
LCD CONTROL PANEL (figure B)
B1. Power button
B3. TIMER button
B5. SLEEP button
B7. Water shortage indicator
B9. MIST intensity indicator 1/2/3 drops (weak / medium / strong)
B10. Night Light button
B12. SLEEP function indicator
USING (picture C)
1.After transportation in low temperatures, leave the appliance in the room for 2 hours to acclimate before using. Do not use the device
without water.
2.Make sure the device is unplugged.
3.Remove the water tank cover (A5). Remove the water tank (A2) from the base of the device (A3)
4.Top up the water tank (A2) only when the machine is switched off from the power supply. Do not pour water into the tank above the
maximum level – look at picture C . Do not pour water into the housing gaps and into the mist outlet pipe shown in Picture C.
5.Place the filled water tank on the base (A3) in correct position, make sure the filter (A7) is properly placed. Wait a 1-2 minutes before
starting the device.
6.Close the water tank cover (A5).
7.Slide out of the fragrance box from the base (A3) and put aroma oil on the aroma sponge (A8) if you desire, 3-5 drops of oil on the
sponge should be enough. Aroma oil is not included in set. Do not add any aromatic substances into the water tank A2 (powder, liquids
oil, etc.). Aromatic oil should be poured only on the sponge (A8) located in the fragrance box in the bottom of unit from back side.
8.Remove plastic insert from the remote control (A6) to active the battery. The remote control (A6) operates the device in the same way
as the control panel buttons on the device housing (picture B).
9.Connect the device to the power supply. The device will emit a single sound and will wait for setting the operating mode.
10.Touch the power button (B1), the LCD screen will light up and the device will start working. The display will show the humidity % near
the machine and the function you set. The mist will start come out after several seconds.
11. Press the SPEED (B2) button one, two or three times to activate continuous mist output at low or medium or strong level.
12.Press the TIMER button (B3) to set the delayed switch-off of device, adjust required time in range: 1-12 hours. The device will switch
off after required time of continuous operation.
13.Press the button (B4) to set required humidity from 45% to 90%.
Note: When the device is on, it shows the current humidity level in room. When the room reaches the humidity % you set, the device will
stop working automatically. When the humidity % decrease and becomes less than the preset humidity %, the device will start working
again. If you don't set the room humidity, the device will keep running until the water is over. The humidifier mainly shows the humidity
near the machine.
14. Press the LIGHT button (B10) to turn on and turn off the night light. The night light will change colors.
15. Press the SLEEP button (B5) to set the LCD display illumination ON/OFF.
16. Press the power button ON/OFF (B1) again so that the device stops working and goes into standby mode. Unplug the power plug.
If there is not enough water in the water tank, the device will beep and the display will show water shortage indication (B7) and have
beep indication voice. The delayed switch-off and constant humidity setting is canceled. The device will stop working after some
seconds. Unplug the device and refill the water tank.
Note: If moisture collects around the appliance, this is not a defect. It may be an indication that the humidity level is set too high. Reduce
the mist output or reduce the required value of humidity %. It is normal to hear dripping sound when the mist output is at high level.
A2. Water tank
A4. LCD Control panel
A6. Remote control
A8. Sponge in fragrance box
B2. Mist SPEED button
B4. HUMIDITY button %
B6. Timer indicator 1-12 hours
B8. HUMIDITY value indicator %
B11. Night Light indicator
B13. HUMIDITY function indicator
6
Publicidad
